manualshive.com logo in svg

Xerox 4235, Руководство по планированию установки, Страница: 49 / 148

Поделиться
Скачать
Xerox 4235 Скачать руководство пользователя страница 49

PRINTER SETUP

XEROX 4235 LPS INSTALLATION PLANNING GUIDE

4-7

Printer setup options–XScript

Table 4-3 lists the printer setup options for XScript.  Based on
your choices, complete Checklist 4:  Printer setup options–
XScript (figure 4-3).  Your Xerox service representative uses the
checklist during installation.

Table 4-3.

XScript printer setup options

Settings

Options
(defaults appear bold)

Description

Document Error
Handling

Print Status Sheet
Do Not Print Status
Sheet

Print Status Sheet–Status sheets print automatically if errors
occur during a job run and/or if a status sheet request was
made by the user.
Do Not Print Status Sheet–No status sheets print.

Offset on job
boundary

Enable
Disable

Defines when and if print jobs are offset in the high capacity
stacker and top output tray.  When enabled, print jobs are
offset in the output trays at the beginning of each job.

Reset Formatter

Reset Formatter
Do not Reset Formatter

Enabling this feature causes the printer to reset the XScript
formatter to avoid an excess accumulation of virtual memory.

Restore factory
defaults

Restore defaults
Do Not Restore
Defaults

Restore defaults resets the option settings within the XScript
printing mode to the factory defaults.
Do not restore defaults does not reset any of the XScript
printing mode option settings.

General features
Auto Tray Switching Enable

Disable

Enable allows the 4235 LPS to feed paper from paper tray 4
when paper tray 1 is empty, and then feed from paper tray 1
when paper tray 4 is empty.

Special feed stock in
paper tray 1

Enable
Disable

Enable specifies whether label stock or other special paper is
currently loaded into paper tray 1.*

Special feed stock in
paper tray 2

Enable
Disable

Enable specifies whether label stock or other special paper is
currently loaded into paper tray 2.*

Special feed stock in
paper tray 3

Enable
Disable

Enable specifies whether label stock or other special paper is
currently loaded into paper tray 3.*

Special feed stock in
paper tray 4

Enable
Disable

Enable specifies whether label stock or other special paper is
currently loaded into paper tray 4.*

Predrilled paper

Enable
Disable

Enable specifies whether predrilled paper stock is currently
loaded.  When enabled, the 4235 LPS assumes that all paper
trays contain predrilled paper.

*

Before you enable these features, have a Xerox service representative define special feed parameters.
Most feed stocks perform satisfactorily without the enhancement of these settings.  (Refer to the Xerox
4235 Laser Printing System Problem Solving Guide for more information.)

Содержание 4235





















































































































































Отзывы:

Нет отзывов