background image

 

Wireless  LED  HeadLight  System  (L2SWE)                                                                                                  www.xenosys.co.kr 

 

1. The battery pack for L2SWE is Lithium-Polymer rechargeable one. 

2.  When  transporting  only  battery,  make  sure  to  keep  it  in  soft  case.  Do  not  make  any 

conductor to connect the battery charging point. 

3.  The  battery  operating  time  may  shorten  using  in  the  cold  place  (below  (-10℃)  even  fully 

charged  one.  In  that  case,  warm  up  the  battery  within  the  pocket  before  using  L2SW.  Do 

not heat up the battery with microwave or any heater. 

4. Use only the charger which is provided by Xenosys. 

5. Charger battery in the range of 0℃  ~ 40℃. It may take longer to charger the battery out of 

this temperature range. 

6.  Provided  battery  can  be  charged  and  discharged  about  300  times  at  room  temperature. 

Lithium-ion battery is expendables, thus if the operating time is shortened after full charge, 

we recommend exchanging new battery.   

7.  Be  careful  on  benzene,  thinner,  alcohol  (volatile  &  flammable  fluid)  and  water.  If  those 

chemicals penetrate the battery, it may cause the trouble in circuit and any accident. 

8.  If  there  is  any  swollen  battery,  spill,  emit,  or  fire,  stop  using  immediately  and  contact  the 

distributor (dealer) or the manufacturer. 

9. Never use any damaged battery and charger. 

10.  In  case  of  the  first  installation  or  unused  long  time,  then  charge  the  battery  fully  before 

using. 

 

  Warning for Charging 

1.  Do  not  connect  any  metallic  objects  between  the  cradle  connector  and  battery.  This  may 

cause the defective on the charger and charger cradle.   

2. Use only the charger which is provided by Xenosys on the phone jack. This may cause the 

defective on the charger and charger cradle. 

  Warning for Disposal 

1.

 

In  case  of  careless  disposal,  it  may  pollute  the  environment,  so  make  sure  to  separate 

collection. 

Содержание L2SWE



























Отзывы: