xenium X-ONE Скачать руководство пользователя страница 6

X- O N E

17

FUNCTIONS AND OPERATIONAL CONTROLS

1

The 

MASTER OUT / SLAVE IN RCA jacks 

are suitable to connect an additional amplifier in MASTER/SLAVE mode.

Attend therefor the chapter 

Interconnection Example: MASTER/SLAVE

 on page 19.

3

The 

BASS BOOST

 controller adjusts the bass enhancement between 0db and +12dB.

6

The 

LOW PASS controller

 adjusts the cut-off point of the frequency range to above. The cut-off frequency is continuously

adjustable from 40 Hz to 180 Hz.

The 

LINE INPUT RCA jacks 

must be connected with the RCA output jacks of the headunit. Both jacks must be used. If your

headunit provide only one RCA jack, you need to split the signal with a y-connector.

2

4

5

The 

INPUT LEVEL controller 

adjusts the input sensitivity of the amplifier to align the audio signal from the head unit.

The input sensitivity is adjustable from 6 to 0.2 Volts.

7

The 

SUB SONIC controller

 (Subsonicfilter) limits the ultralow and not hearable frequencies of the audiosignal to below, to avoid

a mechanical and electical overloading on the subwoofer. The cut-off frequency is adjustable from 15 to 55 Hz and depends on
the size of the subwoofer.

8

The 

SLAVE IN/MASTER OUT switch 

selects the required operation mode of the amplifier.

In the 

SLAVE-Mode

 the amplifier works as a SLAVE amp, this means only the audiosignal of the MASTER amp will be amplified.

All controllers on the SLAVE Amp are without function and will be assumed by the MASTER amp.

In the 

MASTER-Mode

 (Low Pass mode) you are able to limit the frequencies to above with the LOW PASS controller. All controllers

are active. 

NOTE: By using only one amplifier, the Mode-Switch must set to the position MASTER OUT.

6

7

8

1

4

3

5

2

Connect the 

REMOTE port

 with the bass remote controller (only in the MASTER mode). The bass remote controller adjust the

bass level e.g. out of the driver’s seat. Please use only the enclosed bass remote controller and cable.

Содержание X-ONE














Отзывы: