manualshive.com logo in svg
background image

P

REVENTATIVE

 M

AINTENANCE

P

  

  

  

  

  

  

  

  

  

  

  

  

  

  

AGE

 10 

E

E

QUIPMENT

QUIPMENT

M

M

AINTENANCE

AINTENANCE

 

 

Use a dampened soft-cloth to wipe equipment free of perspiration after each use. Avoid getting        

excessive moisture on computer or electronic components. Do not use abrasive cleaners or

petroleum-based solvents to clean equipment. 

 

Do not remove drive train shrouds or attempt any technical service on equipment without consulting  

an authorized service representative.

 

Regularly inspect product for lose assembly hardware and worn components.  

 

(If applicable) For added safety, unplug equipment from the wall socket when it is not being used. 

 

Use a product /exercise mat underneath equipment for protection of floors & carpets. 

 

(If applicable) Apply recommended component lubricants at the required time periods. 

 

Keep product assembly manual, purchase receipt, and service records in a safe storage place.  

 

( If applicable) Periodically check batteries for proper voltage output & replace as needed. 

 

Do not store or use equipment outdoors.  

 

Moving equipment:  

 

Lift up the rear stabilizer and carefully tip the bike forward until the front stabilizer wheels touch

 

the floor. Do not use the computer or pivot arms to move the unit

You may wish to lock the fan in 

 

place (which will keep the arms from moving), by turning the safety knob (referenced on page 7) 

 

until it makes contact with the fan wheel.

 

TRAINING FOR SUCCESS

TRAINING FOR SUCCESS

How you start an exercise program depends on your physical condition. If you have been inactive 
for awhile or you have pre-existing health condition, you should start slowly. Initially you may only 
be able to exercise for a short amount of time using minimal resistance levels or weight loads.  

Begin  your  desired  training  program  slowly  and  gradually  increase  the  amount  of  time  you       
exercise.  Apply  realistic  goals,  that  have  been  set  by  you  or  your  physician.  You  should  see           
sufficient gains in your personal fitness level within 6-8 weeks of continuous exercise, but do not be 
discouraged  if  it takes  longer. It is  very  important  to  exercise  at  your  own  pace  and  become        
confident in obtaining your goals. It is also important to apply warm-up, stretching, and cool down 
periods with any exercise  program.

As your fitness level increases, so  will  your  confidence  and  sense  of  accomplishment.  Regular      
exercise and a healthy diet will energize you and offer a sense of well-being.

 

Содержание ABMG-3

















Отзывы: