manualshive.com logo in svg

Xceltronix i-touch, Руководство по установке и инструкция пользователя, Страница: 14 / 23

Поделиться
Скачать
Xceltronix i-touch Скачать руководство пользователя страница 14

14 

Adding a Permanent Access Code 
 

 

(Requires Master User authorization) 

 

1. 

Press the 

FUNC

 key followed by the 

4/ADD CODE

 key. 

2. 

Input MF, or input MC and the 

ENTER

 key. 

3. 

If room exists for input of another permanent access code (a total of 29 
temporary / permanent access codes are allowed, not including the MC), 
the 

INPUT

 LED will be lit. If the 

ERROR

 LED flashes, either the Master 

User Authorization failed or there is no remaining room for additional ac-
cess codes to be entered. 

4. 

If the 

INPUT

 LED is lit, enter a 4-6 digit permanent access code followed 

by the 

ENTER

 key.  

5. 

If the permanent access code addition was successful, the 

ACCEPT

 LED 

will flash. 

6.   If finished with the batch of code additions, perform 

i-touch™ / Auto-

closer™

 synchronization procedure. 

 

 

NOTE: Users can add their code(s) into the table in the back of this manual.

 

 
Deleting A Temporary Or Permanent Access Code 
 

 

(Requires Master User authorization) 

 

1. 

Press the 

FUNC

 key then the 

8/DEL CODE

 key. 

2. 

Input MF, or input MC and the 

ENTER

 key. If the Master User Authoriza-

tion is successful, the 

ACCEPT

 LED will flash, followed by a solid 

INPUT

 

LED. 

3.      Input the code to be deleted and press the 

ENTER

 key. (NOTE:  MC can 

  not be deleted in this manner.) 

4.      If the code was successfully deleted, the 

ACCEPT

 LED will flash. 

5.   If finished with the batch of code deletions, perform 

i-touch™ / Auto-

closer™

 synchronization procedure. 

 

 

NOTE: Master can remove this/these code(s) from the table in the back of  

 

 

this manual.

 

 

Instructions

 

Содержание i-touch
























Отзывы:

Нет отзывов