background image

MAG 5, 10, 15, 24 

Safety and operating instructions 

 

© 2010 Xcalibre Equipment Limited | 67020101 | 2010-05-25 
Original instructions 

13 

 

Hydraulic oil 

In order to protect the environment, Xcalibre 
Equipment recommends the use of biologically 
degradable hydraulic oil. No other fluids should be 
used. 

  Viscosity (preferred) 20-40 cSt. 

  Viscosity (permitted) 15-100 cSt. 

  Viscosity index Min. 100. 

Standard mineral or synthetic oil can be used. 
Make sure to only use clean oil and filling 
equipment. 

When the machine is used continuously, the oil 
temperature will stabilise at a level which is called 
the working temperature. This will, depending on 
the type of work and the cooling capacity of the 
hydraulic system, be between 20-40°C (68-104°F) 
above the ambient temperature. At working 
temperature, the oil viscosity must lie within the 
preferred limits. The viscosity index indicates the 
connection between viscosity and temperature. A 
high viscosity is therefore preferred, because the 
oil can then be used within a wider temperature 
range. The machine shall not be used, if oil 
viscosity fails to remain within the permitted area, 
or if the working temperature of the oil does not fall 
between 20°C (68°F) and 70°C (158°F). 

 

Pressure adjustment 

The maximum pressure of the power source is 
important. The pressure created in case of an 
incorrectly or unfitted return line coupling would 
cause overloading which could harm the machine 
and result in bodily injuries. The maximum 
pressure of the power source is 160 bar (limited by 
safety valve adjustment). 

 

▲ 

WARNING  Operating pressure 

If the maximum operating pressure for the 
hydraulic machine is exceeded, it can result in 
material damage and personal injury. 

► 

Always run the hydraulic machine with the 
correct operating pressure, see 'Technical data'. 

► 

Only readjust the pressure relief valve (torque 
control) on the machine according to procedure 
and values described under maintenance. Note 
that higher settings might lead to a higher 
torque, which could harm the machine and 
result in serious injury or death. 

 

 

 

 

Water flushing 

For diamond bit core drilling, water flushing is 
required. Mount the water swivel and water hose 
on the core drill as follows. 

 

 

The water can be supplied directly from a source, 
or a separate water kit can be used. A separate 
water kit with pressure tank is available, see the 
spare parts list. 

Содержание MAGNUM





















Отзывы: