6
Installation
WARNING:
Ensure the power
cord is not installed so that it is
pinched or against a sharp edge
and ensure that the power cord is
stored or secured to avoid tripping
or snagging to reduce the risk
of fire, electric shock or injury to
persons.
Grounding Instructions
This product must be grounded.
If it should malfunction or break
-
down, grounding provides a path
of least resistance for electric
current to reduce the risk of
electric shock. This product is
equipped with a cord having an
equipment-grounding conductor
and a grounding plug. The plug
must be plugged into an appropri
-
ate outlet that is properly installed
and grounded in accordance with
all local codes and ordinances.
DANGER:
Improper connec
-
tion of the equipment-grounding
conductor can result in a risk
of electric shock. Check with a
qualified electrician or serviceman
if you are in doubt as to whether
the product is properly grounded.
Do not modify the plug provided
with the product – if it will not fit
the outlet, have a proper outlet
installed by a qualified electrician.
This product is for use on a
nominal 120-volt circuit and has
a grounding plug that looks like
the plug in Figure 1. Make sure
that the product is connected to
an outlet having the same con
-
figuration as the plug. No adapter
should be used with this product.
CAUTION:
Risk of Electric
Shock. This product has two
cords. Unplug both cords before
moving or servicing this furnishing.
!
NOTE:
A 15 Amp, 120 Volt cir
-
cuit is required. A dedicated circuit
is preferred but not essential in
all cases. A dedicated circuit will
be required if, after installation,
the circuit breaker trips or fuse
blows on a regular basis when the
cassette is operating. Additional
appliances on the same circuit
may exceed the current rating of
the circuit breaker.
Mantel Installation
Install the fireplace into the
mantel (refer to mantel assembly
instructions).
Figure 1
7
FRONT
üüü
(30.0 mm)
1.2 in.
(30.0 mm)
3.5 in.
(90.0 mm)
3.1 in.
(80.0 mm)
4.8 in.
(122.0 mm)
5.4 in.
(137.0 mm)
Installation
Figure 2
New Construction
1. Mark the desired location on
the floor and store the fireplace
in a safe, dry and dust free
location.
2.
Use studs to frame
an enclo-
sure with the following
mini-
mum
internal/opening dimen
-
sions (Figure 2).
!
NOTE:
An air inlet is required
for optimum mist production, see
Figure 2 for
minimum
dimen-
sions.
!
NOTE:
For optimal perfor
-
mance, the following
minimum
clearances between the instal
-
lation surface and any surface
above should be maintained:
• Cassette Only: 12 in. (305 mm)
• Cassette with
Xaralyn
heater:
19 in. (483 mm)
Figure 3
3.
Secure unit through the two
holes in the bottom of the unit
into supports to prevent the
unit from hanging from the top
flange, see figure 3 for dimen
-
sions.
4.
The unit is equipped with a
power supply plug and a fused
receptacle (Figure 4), the plug
should be plugged
directly into
a 15 A, 120 V outlet.
CAUTION:
During operation
8.5 in.
(216mm)
6.7 in.
(170mm)
Air Inlet
DFI400: 100cm
2
DFI600: 150cm
2
Supports: 0.75 in (19 mm) high
Exit for Cord
DFI400: 15.75 in. (400mm)
DFI600: 22.05 in. (560mm)
Installation
Surface
Содержание Optimyst
Страница 10: ......
