Xantrex XC3012 Скачать руководство пользователя страница 6

Страница: 6 / 80

About This Guide

975-0187-01-01

Conventions Used

The following conventions are used in this guide.

This Guide contains information for four versions of the XC Series.

The Xantrex XC3012 Battery Charger (12 V, 30 A) will be referred to as the
XC3012 when it is being referenced individually.

The Xantrex XC5012 Battery Charger (12 V, 50 A) will be referred to as the
XC5012 when it is being referenced individually.

The Xantrex XC1524 Battery Charger (24 V, 15 A) will be referred to as the
XC1524 when it is being referenced individually.

The Xantrex XC2524 Battery Charger (24 V, 25 A) will be referred to as the
XC2524 when it is being referenced individually.

When the Xantrex XC3012, XC5012, XC1524 and XC2524 Battery Chargers are
being referenced together, they will be referred to as the XC Series.

Related Information

You can find more information about Xantrex Technology Inc. as well as its
products and services at www.xantrex.com

WARNING

Warnings identify conditions or practices that could result in personal injury or loss of life

CAUTION

Cautions identify conditions or practices that could result in damage to the unit or other
equipment.

Important:

These notes describe things which are important for you to know, but not as

serious as a caution or warning.

XC_Charger_Owner.book Page iv Friday, August 12, 2005 3:23 PM

Содержание XC3012

















































































Результаты поиска

Содержание XC3012

Отзывы:

Xantrex XC3012, Руководство пользователя, Страница: 6 / 80

Результаты поиска

Содержание XC3012

Отзывы: