Xantrex XC3012 Скачать руководство пользователя страница 18

Страница: 18 / 80

Introduction

1–6

975-0187-01-01

Onboard Status Panel

This section describes the parts of the onboard status panel of the XC Series.
Figure 1-3 shows the panel.

Figure 1-3

XC Series Onboard Status Panel

Item Description

Charge Current
•

Displays the output charge current in % of charger maximum for the bank being charged

•

100% indicator light flashes to indicate battery temperature too high (> 50 °C, 122 °F)

•

10% indicator light flashes to indicate battery temperature too low (< 0 °C, 32 °F)

•

25% indicator light flashes to indicate that a battery has been disqualified (see page 3–4)

Charger Status -

READY

•

Ready indicator light illuminated indicates all batteries are fully charged, and are now in
float or rest

Charger Status -

CHARGING

•

Charging indicator light illuminated indicates unit is performing a normal charge cycle

•

Charging indicator light flashing indicates that the unit is performing an equalization cycle

Charger Status -

FAULT

•

Fault indicator light continuously illuminated indicates any fault condition that prevents
the XC Series from charging one or more batteries, but is not a charger failure - remote
display shows details of fault

•

Fault indicator light flashing indicates the XC Series has experienced a charger failure -
remote display shows

err followed by CHf

2
3
4

XC_Charger_Owner.book Page 6 Friday, August 12, 2005 3:23 PM

Содержание XC3012

















































































Результаты поиска

Содержание XC3012

Отзывы:

Xantrex XC3012, Руководство пользователя, Страница: 18 / 80

Результаты поиска

Содержание XC3012

Отзывы: