background image

Xantrex RV Series Inverter/Charger Owner’s Manual

23

User Menu

The ON/OFF switch on the RC7 operates the same as the inverter’s ON/OFF switch. In order for
the RC7 to remotely power up the inverter, the inverter must be started up with the RC7
connected so the inverter knows it is present. Once this has been done the inverter’s power
switch should be left in the 

on

 position and the RC7 used to turn it on and off. When pressed to

turn on, the RC7 will beep and go through a power-up routine, after which it will go to the 

User

Menu

. In this mode the display will show the inverter’s status and monitor batteries. Pressing the

Menu Item

 buttons will scroll the display vertically, and the 

Settings

 button will cycle the display

left to the next item in the menu tree.

RC7 Remote Control Faceplate

The system status mode is the first mode you will see. It monitors and displays all of the inverter’s
activities—it shows what the inverter is “thinking.” The following indications will be shown under
the System Status heading.

Waiting for AC:

 This shows that the inverter is waiting for an AC input. Once AC is present the

inverter will switch to charger mode and begin charging the batteries.

Searching: 

The inverter is in search sense mode and is “looking” for loads to run. 

Inverter

 LED

will flash.

Inverting:

 Shows that the inverter is taking power from the batteries and inverting it to 120 VAC,

60 Hz power. This will also be shown on the LED labeled 

inverter 

as a solid green light

Bulk Charging/Absorption Chg/Float Charging:

 These indicators show the charger section is

working and define which of the three stages of charge the charger is in. See “Three Stage
Battery Charging” on page 7 f
or details. The 

charge

 LED to the left of the LCD display will be on

solid when the inverter is in the charger mode.

Hibat/Stop Chrg:

 The batteries’ voltage is too high and the charger has shut down. The 

Batt.

Full

 LED will begin to flash when the batteries reach 90% of their maximum charge capacity. As

the batteries continue to charge toward 100% the LED will stay on longer and longer until, at
100% charge, it will remain on steadily. Once the batteries reach 100% charge the charger will go
into the float mode.

Inverter LED:

Flashing= Search Mode
Solid= Inverting

Battery Full LED:

Begins flashing at 90%
full, and stays on longer
as charge increases. At
100% charge LED is on
steady

System Status:
Waiting for AC

Charge LED:

Solid when charging

Error LED:

Solid= Error condition.
See display for
explanation of the error

Содержание RV2012, RV2512, RV3012













































Отзывы: