background image

Operation

4–2

Turning the Inverter On and Off

The On/Off switch on the inverter’s front panel turns the control circuit in 
the PROwatt 3000 on and off.

To turn the inverter on and off from its front panel:

Turn the inverter’s On/Off switch on or off.

Using the Remote On/Off Switch

To operate the inverter from the remote 

On/Off

 switch:

1. Turn On the inverter’s On/Off switch.

 

The inverter is now On and the 

INVERTER ON

 indicator on the remote switch lights up.

.

2. Press the touch control button on the remote switch to turn the 

inverter off. The 

INVERTER ON 

indicator goes off.

Press the button again if you want to turn the inverter On. 

Turning the Inverter Off Between Charges

When the On/Off switch is on but no power is being supplied to a load, 
the inverter draws less than 600 mA from the battery. This is a low current 
draw. It would take more than a week to discharge a 100 Ah battery at this 
current, so you don’t have to worry about excessive drain on your battery 
if you leave the inverter switched on for a few days.

If you are not planning to recharge your battery within a week or so, 
switch the inverter off. When the switch is Off, the inverter draws less 
than 200 

µ

A from the battery.

WARNING: Electrical Shock Hazard

The inverter’s On/Off switch does not disconnect power from 
the PROwatt 3000.

Note

:

Leave this switch on during operation. Turning it off disables 

the remote switch.

Содержание PROwatt 3000



















































































Отзывы: