Xantrex 817-1050 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 90

Xantrex 817-1050 Скачать руководство пользователя страница 43

975-0784-01-01

29

Basic Installation Procedures

This

section for use by

qualified per

sonnel

only.

13. Route the negative cable through the right side strain relief

clamp and connect the cable from the negative post of the
battery to the negative DC terminal of the inverter.

14. Fasten the DC terminal nut (set aside earlier) to the terminal

bolt. Tighten the nut to a torque of 71–80 in-lbf (8–9 N-m). Do
not overtighten. Make the connection snug enough so the cable
lug does not move around on the DC terminal. Center it through
the DC knockout hole and do not let it touch the edge.

15. Replace the DC compartment cover.

DC Grounding

To connect the DC ground:

The equipment grounding lug on the DC end of the Freedom XC is
used to connect the chassis of the Freedom XC to your system’s DC
negative connection or grounding bus point as required by electrical
regulations. Use copper wire that is either bare or provided with
green insulation. Do not use the DC Ground Lug for your AC
grounding. See the AC wiring instructions in this section.
Follow the guidelines below that correspond to the specific type of
installation. These guidelines assume you are using the DC supply
cable and fuse sizes recommended in this manual. If you are using
different sizes, refer to the applicable installation code for DC
grounding details.

Recreational Vehicle

Use 8AWG copper wire and connect it

between the Chassis Ground lug and the vehicle’s DC grounding
point (usually the vehicle chassis or a dedicated DC ground bus).

Marine

Use copper wire that is bare or has insulation rated

minimum 105 °C, and connect it between the Chassis Ground lug
and the boat’s DC grounding bus or engine negative bus. For the
Freedom XC 1000, use a wire of gauge 3AWG minimum. For the
Freedom XC 2000, use a wire of gauge 1/0AWG minimum.



WARNING

FIRE HAZARD

Do not complete the next step if flammable fumes are present. Explosion
or fire may result if the disconnect/battery selector switch is not in the off
position. Thoroughly ventilate the battery compartment before making
this connection.

Failure to follow these instructions can result in death or serious injury.

Freedom XC Series INV-CHG Owners Guide.book Page 29 Wednesday, June 7, 2017 3:13 PM

«
...
41
42
43
44
45
...
»

Содержание 817-1050



























































































Отзывы:

Нет отзывов