background image

975-0697-01-01

19

Installing the Inverter/Charger

This guide for use by qualified installers only.

Step 1: Choosing a Location for the Inverter/Charger

The inverter should only be installed in a location that meets 
the following requirements:

FIRE AND EXPLOSION HAZARD

This equipment contains components that could produce arcs or sparks.
To reduce the risk of fire or explosion, do not install this equipment in
compartments containing batteries or flammable materials, or in locations
that require ignition-protected equipment. This includes any space
containing gasoline-powered machinery, fuel tanks, or joints, fittings, or
other connections between components of the fuel system.

Failure to follow these instructions will result in death or serious injury.

HEAT HAZARD

Do not cover or obstruct the ventilation openings. Do not install this
equipment in a compartment with limited airflow. Overheating may result.

Failure to follow these instructions can result in minor or moderate injury.

Ventilated

Do not operate the inverter/charger in a closed-in 
area or restrict ventilation in any way. The inverter/
charger requires air circulation to maintain 
optimum operating temperature and provide best 
performance. If the unit has inadequate ventilation, 
it may shut down due to overheating. 
The air vented through the openings should also 
have a path to circulate away from the inverter/
charger.

Dry

Do not allow water or other fluids to drip or splash 
on the inverter/charger. Do not expose to rain, snow 
or water.
Use an optional inverter drip shield (PN: 808-9004) 
for marine installations.

Cool

Normal air temperature should be between
0 °C and 60 °C—the cooler the better within this 
range.

Clearance

Allow as much space around the inverter/charger as 
possible. It is recommended that other objects and 
surfaces be at least 76 mm away from the 
ventilation openings for best performance.

FSW 230V Installation Guide.book  Page 19  Tuesday, August 7, 2018  9:18 AM

Содержание 815-2524-02























































































Отзывы: