manualshive.com logo in svg

Xantrex 807-1055, Руководство пользователя

Поделиться
Скачать
Xantrex 807-1055 Скачать руководство пользователя страница 9

975-0727-01-01

vii

Precautions When Working With Batteries

Battery work and maintenance must be done by qualified 

personnel knowledgeable about batteries to ensure compliance with battery 
handling and maintenance safety precautions.

•

Always wear proper, non-absorbent gloves, complete eye protection, 
and clothing protection. Avoid touching your eyes and wiping your 
forehead while working near batteries. See note #4.

•

Remove all personal metal items, like rings, bracelets, and watches 
when working with batteries. See notes #5 and #6 below.

•

Never smoke or allow a spark or flame near the engine or batteries.

•

Never charge a frozen battery.

NOTES:

1.

Mount and place the Freedom HFS Sine Wave Inverter/Charger unit 
away from batteries in a well ventilated compartment.

2.

Always have someone within range of your voice or close enough to 
come to your aid when you work near a lead-acid battery.

3.

Always have plenty of fresh water and soap nearby in case battery acid 
contacts skin, clothing, or eyes.

4.

If battery acid contacts skin or clothing, wash immediately with soap 
and water. If acid enters your eye, immediately flood it with running 
cold water for at least twenty minutes and get medical attention 
immediately.

5.

Use extra caution to reduce the risk of dropping a metal tool on the 
battery. It could spark or short circuit the battery or other electrical 
parts and could cause an explosion.

6.

Batteries can produce a short circuit current high enough to weld a ring 
or metal bracelet or the like to the battery terminal, causing a severe 
burn.

7.

When removing a battery, always remove the negative terminal from 
the battery first for systems with grounded negative. If it is grounded 
positive, remove the positive terminal first. Make sure all loads 
connected to the battery and all accessories are off so you don’t cause 
an arc.

IMPORTANT:

 

BURN FROM HIGH SHORT-CIRCUIT CURRENT, FIRE 
AND EXPLOSION FROM VENTED GASES HAZARDS

Failure to follow these instructions can result in death or serious 
injury.

Freedom HFS IC Owners Guide.book  Page vii  Friday, September 11, 2015  2:54 PM

Содержание 807-1055



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды