5. Setting up the Security Console (SC28)
5.1 Setting the clock
1. To access the menu, press either the menu UP ?
or DOWN ?
button. The display now shows
ENTER PIN
.
2. Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). The display is cleared
and shows a * for each number entered.
3. When the PIN code has been entered correctly, the word
INSTALL
will show up on the display.
4. Use the menu buttons UP/DOWN ?
to go to menu item
2. SET CLOCK
. Press OK to select this menu item. You can
also go to this menu item directly by pressing a 2 on the number pad.
5. Use the menu buttons UP/DOWN ?
to select the correct day of the week.
6. Use the number pad to enter the new time (24 hour notation), followed by OK. The display now reads
INSTALL
.
7. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes,
you will quit the menu. If you choose No, you go back to the first menu item. .
If you press CLEAR while entering the time, the time entered will be deleted.
5.2 Storing phone numbers
The SC28 console has a built-in telephone dialler. In case of an alarm up to 6 telephone numbers can be
dialled. All persons called will be able to listen to the message you have recorded (5.3). The message needs to
be confirmed by the person answering the phone by pressing a 0 on their phone (DTMF response). The dialler
then knows the next number does not need to be called.
NOTE: You are not allowed to use emergency numbers, i.e. the police and security companies, unless
you have been granted permission.
First make a list with the phone numbers you want to enter, in the order they need to be dialled. If you have
connected the console via an PABX phone system, you may need to add a 0, or possible other digit in front of
the telephone number to get an external land line.
1. To access the menu, press either the menu UP?
or DOWN?
button. The display now shows
ENTER PIN.
2. Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). The display is cleared
and shows a * for each number entered.
3. When the PIN code has been entered correctly, the word
INSTALL
will displayed.
4. Use the menu buttons UP/DOWN?
to go to menu item
3. PHONE NUMS.
Press OK to select this menu item. You
can also go to this menu item directly by pressing a 3 on the number pad.
5. Use the menu buttons UP/DOWN ?
to go to the memory space where you want to enter a telephone number
(
PHONE 1, PHONE 2 … PHONE 6
).
6. Press OK when you have arrived at the memory space. After pressing OK at PHONE 1, the display will read
SET PH 1.
7. Enter the telephone number. Press the OFF button for a dial pause (use a dial pause between the extra 0 and
the telephone number when the console is connected to a PABX phone system. A small letter
P
can now be
noticed on the display).
8. Press OK. You will now automatically go to the next memory space.
9. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes,
you will quit the menu. If you choose No, you go back to the first menu item. .
If you press CLEAR while entering a telephone number, the number entered will be deleted.
IMPORTANT:
It’s mandatory to have all 6 positions programmed. It’s allowed to program the same number on
different locations, but be aware if you program less than 6 different telephone numbers, the console will try to
contact you at these numbers several times in case of an alarm.
As soon as the call is confirmed by a DTMF “0” press from a phone, the console will stop dialling.
5.3 Recording your own message
You can record an own message that will be used by the telephone dialler. The message can be up to 12
seconds long. Make sure the message is not too short, because this will cause a long silence period when the
message is played and repeated.
Example: “This is the security system of ...... Press 0 after the message to hear what is going on. Please
undertake action as agreed.”
1. To access the menu, press either the menu UP ?or DOWN ?
button. The display now shows
ENTER PIN.
2. Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). The display is cleared
and shows a * for each number entered.
3. When the PIN code has been entered correctly, the word
INSTALL
will show up on the display.
