X-TREME XB-700Li Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 35

X-TREME XB-700Li Скачать руководство пользователя страница 24

24

3.

Follow wire from throttle housing to white connector and unplug.

4.

Loosen small allen head bolt from throttle housing and slide throttle from handlebar.

5.

Place new throttle in place and reconnect new connectors.

How To Check Brake Safety Switch

First remove front fairing and check the throttle connector and brake connectors for loose

connection. Tug on each wire to make sure its locked into the connector.

1.

Open seat and remove the 4 bolts that attaches the seat barrel to the scooter. 2 bolts on each

side of the seat latch and the other 2 are in down in bottom front of seat barrel. Lift off the

seat and seat barrel as one piece.

2.

Location of brake safety connection: You should see a box with several wires coming out of

it. You will also see these wires go into quick disconnects and locate a 4 wire plug. There will

only be one and on the controller side of the connector the wire colors are: Yellow, Red,

Black and Green. On the opposite side the colors are Blue, Green with Yellow stripe, Gray

and Green. Unplug the connector and locate the Blue wire, on the opposite side of the wire

goes into the male connector we will need to unlock the gold pin to remove the wire from the

controller.

How To Test Rear Wheel & Controller

Place scooter up on center kickstand, turn scooter ignition in the "ON" position. Spin rear wheel

by hand and check to see if it falls in one of the following conditions:

A.) Wheel spins with slight resistance – Controller could need replaced

B.) Wheel spins hard like brake engaged – Controller and motor could need replaced

C.) Wheel spins Jerky – Controller and motor could need replaced

How To Check Voltage

Tools Needed: Multi-meter to read VDC

First be sure the battery connector from the scooter is firmly attached to the battery case. Leave all

connectors connected when measuring the voltage by sliding your meter probes into where the

wires go on the backside of the connectors.

Battery Power - 12.65vdc per battery min = +50vdc to turn on the controller.

1.

Across the large Red & Black wires coming out of the controller is main power leads. Should

have +50vdc here.

«
...
22
23
24
25
26
...
»

Содержание XB-700Li




































Отзывы:

Нет отзывов