4. Status LED and wiring description
Device status LED:
GSM LED - Red
Status
Description
Off
Phone module switched off or in “sleep mode”
Blinking
600 ms On / 600 ms Off
SIM card not inserted, Pin code enable (to be
removed) or GSM network authentication in
progress
Blinking
100 ms On / 3 sec Off
GSM network successfully authenticated
Blinking
2 x 100 ms On / 2,5 sec Off
GPRS Server successfully connected
GPS LED (Dual-mode GPS/GLONASS receiver) - Green
Status
Description
Off
GPS/GLONASS receiver switched off or in “sleep
mode”
Blinking
1 sec On / 1 sec Off
Invalid GPS/GLONASS fix
On
GPS/GLONASS position successfully acquired,
valid fix
Attention please:
Before power up the device
it’s necessary to insert the SIM card into the
card reader which is placed on the bottom side
of the device (please remove the black panel in
order to accede the reader).
Attention please:
By using a cell phone, please
disable the SIM card Pin code before inserting it
into the device.
5. Quick start
1- After inserting the SIM card, please turn ON the device by connecting Red
1-
wire (Positive) and Black wire (Negative) to main power supply. Please
1-
connect also White wire (Input 1) to ACC signal (+15) in order to maintain
1-
the device On during the testing procedure. When the device is successfully
1-
connected to power supply then both
red
and
green LED
start blinking.
2- Please wait for few seconds till the phone module successfully authenticate
1-
to the GSM network. When the connection is established then
red LED
1-
starts blinking (2 x 100 ms On / 2,5 sec Off).
3- In order to get the first valid fix, it’s necessary to place the device in an
1-
appropriate place (open sky) avoiding any metal surface obstructing it.
1-
When GPS/GLONASS is fixed then
green LED
lights steady (On).
4- By sending an SMS message to the unit it’s possible to pair your mobile
1-
phone number (up to 2 numbers) and to assign an ID name to the device
1-
(max 12 characters). The SMS string you need to send is:
1-
#CFG*
Cell.1
*
Cell.2
*
Name
#
1-
Example of string you need to send for enabling one SMS phone number
1-
only and for assigning an ID name:
1-
#CFG*
+391234567890
**
X360
#
5- When the device is turned ON and GSM module is ON (red LED is blinking)
1-
it’s possible to query the position from your mobile phone by sending
XPOS
1-
SMS string. Through SMS channel it’s also possible to control a pre-defined
1-
output from remote. To enable the predefined output please send
XON
1-
command string by SMS; to disable it please send
XOFF
command string.
1-
By sending
XCALL
SMS, it’s possible to receive to your mobile phone a
1-
“Silent listening” call from the device (optional external microphone must be
1-
connected to the unit), and also a “2 Ways” call by sending
XCALL2
SMS
1-
string (both optional external microphone and speaker must be connected
1-
to the unit).
1-
Moreover, it’s possible to manage “Auto-Target” function from 3 predefined
1-
sizes of radius: Small, Medium e Large. Based on which radius you want to
1-
enable, the command strings to send by SMS are:
XGEOSON
(Small radius
1-
Target enabled),
XGEOMON
(Medium radius Target enabled) and
1-
XGEOLON
(Large radius Target enabled); to disable them please send:
1-
XGEOSOFF
(Small radius Target disabled),
XGEOMOFF
(Medium radius
1-
Target disabled) and
XGEOLOFF
(Large radius Target disabled).
1-
Only pre-defined numbers from Control Base Center or by CFG SMS self-
1-
setting procedure (please refer to point N.4) are able to manage these
1-
functions.
Attention please:
for a better management and functionality the device must
be pre-configured and fully tested from the reference Control Base Center.
