X-Trax VP-1003 Скачать руководство пользователя страница 30

Страница: 30 / 60

- 30 -

Choose line to set info about SIP, there are 3 lines to choose. You can switch by

【

Load

】

button.

Shows if the phone has been registered the SIP server or not; or

so, show Unapplied;

Server Name

Set the server name.

Server Address

Input your SIP server address.

Server Port

Set your SIP server port.

Account Name

Input your SIP register account name.

Password

Input your SIP register password.

Phone Number

Input the phone number assigned by your VoIP service provider.

Phone will not register if there is no phone number configured.

Display Name

Set the display name.

Proxy Server Address

Set proxy server IP address

（

Usually, Register SIP Server

configuration is the same as Proxy SIP Server. But if your VoIP

service provider give different configurations between Register

SIP Server and Proxy SIP Server, you need make different

settings.

）

Proxy Server Port

Set your Proxy SIP server port.

Proxy Username

Input your Proxy SIP server account.

Proxy Password

Input your Proxy SIP server password.

Domain Realm

Set the sip domain if needed, otherwise this VoIP phone will use

the Register server address as sip domain automatically. (Usually

it is same with registered server and proxy server IP address).

Enable Register

Start to register or not by selecting it or not.

Set expire time of SIP server register, default is 60 seconds. If the

expire time set, the phone will change automatically the time into

the time recommended by the server, and register again.

NAT Keep Alive Interval

Set examining interval of the server, default is 60 seconds

User Agent

Set the user agent if have, the default is VoIP Phone 1.0

Signal Key

Set the key for signal encryption

Media Key

Set the key for RTP encryption

Local port

Set sip port of each line

Ring type

Set ring type of each line

Hot line Number

Set hot line number of each line

Conference Number

Configure conference number in server conference.

Transfer Expire Time

For the phone supports the transfer of certain special features

server, set interval time between sending “bye” and hanging up

after the phone transfers a call.

Содержание VP-1003





























































Результаты поиска

Содержание VP-1003

Отзывы:

Похожие инструкции для VP-1003

Бренды по названию

Популярные бренды

X-Trax VP-1003, Руководство пользователя

Результаты поиска

Содержание VP-1003

Отзывы:

Похожие инструкции для VP-1003

Бренды по названию

Популярные бренды