PB8-087
R/M3x8
P/M3x8
PB8-160-R
PB8-166
PB8-170
PB8-199
PB8-180
PB8-181
PB8-164
R/M3x8
BL(F)/
Ø
10xØ5x4
Note : Please coated the screw glue first when screwing down the flat head screw( M3x8 )and the roud head screw(M3x8).
提 示：锁平头螺丝（
M3x8
）和圆头螺丝（M3x8）时需先涂上螺丝胶。
PB8-087 Spacer
垫片
Ø5.1xØ6.5x0.8
PB8-164 Spacer
垫片
Ø10.1xØ14x1
【P3-2】
Note : Do not too tight or loose at the belt.
提 示：安装时皮带不能过紧或过松。
Note : Please coated the screw glue first when screwing down , the flat head screw (M2.5x6) and the grains(M3x4).
提 示：锁平头螺丝（M2.5x6)和机米（M3x4)时需先涂上螺丝胶.
PB8-087
Spacer 垫片 Ø5.1xØ6.5x0.8
JM/M3x4
JM/M3x4
S3M-129
PB8-030-031
PB8-143-144
PB8-087
R/M2.5x4
PB8-121
PB8-030-031
P/M2.5x6
PB8-031
PB8-030
【P4-1】
【P4-2】
B/M2.5x10
PB8-082
97-A
B/M1.6x8
B/M2x5
R/M2x6
JM/M3x3
PB8-122
PB8-012
PB8-021
PB8-032-J
PM8-122
Spring
弹簧
Ø3x0.4x22
Note :
The Spring should free move ;
d o not too tight or loose.
提 示：安 装 弹 簧 时 不 能 太 松 或 太 紧 。
PB8-012
Steering slide
转向推杆配件
Note : Do not over tighten to ensure free
提 示：安装转向推杆配件不能太紧，需自由活动。
PB8-082
Steering arm wire
转向推杆杆
M2x100mm
Note : If the motorcycle does not run straight even after adjusting the steering trim or steering
movement is not responding properly.It is possible the steering arm is bent. In this case,
please use the include tweezers to gradually, while not operating the steering.
提 示：如果在调整转向微调后摩托车仍然不能直线行驶或者转向正确的方面，很有可能是因为转向螺
纹杆弯曲了，这种情况，请在不操作转向的状态下，通过工具，将转向螺纹杆向中心位置调整。
Note : There are 3 holes to adjust turn in the shock absorbed.the left side is fast turns ,the
right side is for beginner and the middle is default setup
提 示：减震器固定板有
3
个孔可调，左边为快速转弯；右边为初学者；中间为出厂默认设置。
PB8-128
PB8-081
JM/M3x4
Receiver
Note : The crash bar can use different shapes in different site.
提 示：根据不同的场地可选择不同形状的防倾杆
Suitable for smoothness road and high wear resistance.
适合在较为平整的路面使用，优点是耐磨度高。
Suitable for bumpy and rough road , slide like a wheel, reduce the bump.
适合在较为凹凸不平的路面使用，优点像大轮子在地面滑行，减少边角与路面的碰撞，但耐磨度减低。
【P4-3】
PB8-127
PB8-081
R/M3x6
PB8-056
PB8-079
PB8-125
PB8-125
PB8-125
PB8-078
R/M1.6x4
PB8-056
【P4-5】
PB8-021
Braking Servo
P/M2.5x6
B/M2x8
PB8-194
PB8-123
PB8-068
PB8-063
PB8-130
PB8-126
CX108801
PB8-049
B/M2x5
R/M3x8
JM/M3x3
M2
M3
【P4-4】
为升级件需另外购买
are option Parts
PB8-087
R/M3x8
P/M3x8
PB8-160-L
PB8-181
PB8-164
R/M3x8
BL(F)/
Ø
10xØ5x4
PB8-037-038-167
JM/M3x4
S3M-210
Note : Do not too tight or loose at the belt.
Please coated the screw glue first when screwing down the round head
srcew(M3x8)
&The flat head screw(M3x8)
and the grains(M3x4).
提 示：安装时皮带不能过紧或过松。
锁圆头螺丝
(M3x8)
平头螺丝（M3x8）和机米（M3x4）时需先涂上螺丝胶
.
【P3-3】
Note : Please grease the planet gear first when install the gyro pocket. Pls apply the rim and the tire with CA glue after finishing
assembly. When change the tire , please check the bearing have any injured and apply the grear silicone oil.
提 示 : 安装陀螺仪时请在行星齿上添加润滑油；完成陀螺仪安装后请将陀螺仪上下盖与轮胎用快干胶固定；如需更换轮胎请检查轴承
是否损坏 , 同时再添加润滑油。
PB8-087 Spacer
垫片
Ø5.1xØ6.5x0.8
PB8-088 Spacer
垫片
Ø5.1xØ6.5x2.3
PB8-091 Spacer
垫片
Ø5.1xØ6.5x1.8
Note : Please coated the screw glue first
when screwing down the flat head screw(M2x6) .
提 示：锁平头螺丝（
M2x6
）时需先涂上螺丝胶。
【P3-1】
PB8-025
PB8-094
BL/
Ø10xØ5x4
PB8-113
PB8-109
PB8-087
JM/M3x2
PB8-091
PB8-034
PB8-035
P/M2x6
M2
PB8-085
PB8-114
BL/
Ø10xØ5x4
BL/
Ø10xØ5x4
BL/
Ø8xØ5x2.5
PB8-084
B/M2x8
P/M2x10
PB8-111-1
PB8-086
BL(F)/
Ø9xØ5x3
PB8-116
PB8-168
PB8-088
