Copyright © 2015 WyreStorm Technologies |
SW-0402-MV-HDxx Quickstart Guide | 160330
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
3 of 4
HDMI/HDBaseT Wiring
IMPORTANT!
HDMI Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables,
and electrical or environmental interference can have an adverse
effect on HDMI or HDBaseT transmission limiting performance. Steps
should be taken to minimize these factors (or remove completely)
during installation for best results.
• While similar in nature, the HDBaseT protocol is different than Ethernet
and voltages provided for PoH can be higher than those provided by
PoE. For this reason, never connect an HDBaseT link to an Ethernet
router or switch to avoid damaging the connected devices
Wiring for HDBaseT follows the EIA T568B standard.
Pin 1 Pin 8
Wire colors shown follow EIA/TIA-568B standard.
Pin 1:
Pin 2:
Pin 3:
Pin 4:
Pin 5:
Pin 6:
Pin 7:
Pin 8:
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
Supported Video Resolutions
Cable Type
Range
Supported Resolution
Cat5e
70m/230ft
1080p@60Hz 36bit
70m/230ft
1080p@60Hz 3D
Cat6/6a
35m/115ft
4K@60Hz 4:2:0 24bit
Local Area Network (LAN) Wiring
LAN wiring follows the EIA T568B standard
Pin 1 Pin 8
Wire colors shown follow EIA/TIA-568B standard.
Pin 1:
Pin 2:
Pin 3:
Pin 4:
Pin 5:
Pin 6:
Pin 7:
Pin 8:
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
Line In Wiring
Connection for Line In uses a 3.5mm (1/8in) stereo connector.
Tip:
Ring:
Left Channel
Right Channel
Sleeve: Ground (GND)
Audio In Wiring
Connection for Audio In uses an RCA Male connector for the left and the
right inputs.
Tip:
Audio Postive (+)
Shield: Audio Negative (-)
YUV/CVBS (Component/Composite Video) Wiring
Connection for CVBS inputs use an RCA Male connector for each of the
individual connections.
Tip:
Video Signal (+)
Shield: Video Ground (GND)
IR Wiring
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that
o5V DC to power the included IR receiver.
IMPORTANT IR TX Connection Guidelines!
• 3rd party IR receivers may require a different voltage, refer to the
documentation provided with the IR receiver before making any
connections to avoid damaging the device.
• When connecting to an IR control system use the WyreStorm CAB-IR-
LINK stereo to mono cable to remove the 5V DC.
Tip:
Ring:
IR Signal
+5V DC
Sleeve: Ground (GND)
RS-232 Wiring
RS-232 Connection Guidelines
The following wiring diagram shows the pinouts for the switcher. While
not shown, connect the TX (transmit) to RX (receive) pins at the control
system or PC side of the cable.
Most control systems and computers are DTE where pin 2 is RX, this can
vary from device to device. Refer to the documentation for the connected
device for pin functionally to ensure that the correct connections can be
made.
Pin 1:
Pin 2:
Pin 3:
Pin 4:
Pin 5:
Pin 6:
Pin 7:
Pin 8:
TX (Transmit)
RX (Receive)
-------
-------
GND (Ground)
Outside of DB9
female chassis port
shown.
-------
-------
-------
Pin 9: -------
5
9
8 7 6
4
3
2
1