Technical Support: [email protected] US: +1 866 677 0053 EU: +44 (0) 1793 230 343
3
FEA
TURES AND SAFETY PRECAUTIONS
Employing a switching topology, the low voltage, energy
efficient digital Class D amplification delivers power to the
speaker load exclusively with very little power wasted in
operation. This increase in efficiency has the main benefit
of lowering heat dissipation and reducing the size of the
amplifier assembly. If properly executed, most D-class
amplifiers typically have a much smaller form factor and a
lower BOM cost than comparable Class-A/AB/B units.
In terms of installation, it can be used locally in-room as a
display device, remotely in-rack or centrally at any point in-
line for one of the most flexible and powerful applications of
HDBaseT technology to date.
The AMP-001-010 is the first product of its kind and
represents WyreStorm’s innate understanding and
appreciation of the AV installation by continually pushing the
boundaries of what is possible to offer innovative products
that add great value to any residential or commercial
application, whatever the size or budget.
www.wyrestorm.com
2. Features
• Combined HDBaseT Repeater, Receiver and Class D Amplifier – all in
one.
• Compact and easy to install & use with single Cat5e/6 cabling –
applies the same basic integration principles for residential, light or
major commercial projects.
• Flexible and versatile – multitudes of application scenarios from basic
extender to complex volume digital AV distribution installed at any
point during a cable run.
• HDBaseT Input and pass-thru with HDBaseT Output.
• 3:1 Audio Switcher/Receiver – Audio from centralized source via
HDBaseT Transmitter or Matrix Device, Audio Return Channel (ARC)
or Local Audio Input via 3.5mm.
• AMP used centrally with AV source, In-line near speakers, wall
mounted near data connections or locally at display location.
• 70m/230ft transmission distance between device and AMP > then
another 70m/230ft to next AMP.
• Fully cascadable up to 7 times from single transmitting device (Matrix
or HDBaseT transmitter).
• HDMI output for direct connection of HD display either in-line to each
AMP connected or at the end of the run.
• 2.1 stereo audio at 25w per channel - amplifier capability to drive
4, 6 & 8 Ohm speaker loads.
• High quality preamplifier adjustment for tone/volume/sub/mute
control.
• Variable Analog line level outputs.
• Analog (RCA) Subwoofer output.
• Stereo speaker amplified outputs with left/right spring terminal
connections.
• Bidirectional control of source and display via IR or RS232 (IR control
signal passed within HDMI transmission).
• Options range from basic control of devices using IR TX and RX ports
to fully integrated control via leading control systems using RS232.
• Commands (Tx, Rx, Gnd) sent with HD Audio & V ideo contained
within a single Cat5e/6
• AMPs addressable via RS23 • RS232 Port for firmware update or
RS232 control signal transmission.
• EDID management and pre-sets via DIP switch.
• LED indication – power status, audio source selection (HDBaseT,
Local or ARC).
• HDMI v1.4 features supported.
• HDCP compliant.
• Internal ESD protection.
• Compact size for flexible integration location.
• Mounting brackets supplied.
.
Part Number
AMP-001-010
3. Safety Precautions
1. Do not expose this apparatus to rain, moisture,
sprays, drips or splashes and ensure that no
objects containing liquids are placed on the
apparatus, including cups, glasses and vases.
2. Do not place this unit in a confined space such as
enclosed shelving, cabinets or bookshelves.
Ensure the unit is adequately ventilated.
3. To prevent the risk of electric shock or fire hazard
due to overheating, do not cover the unit or
obstruct ventilation openings with material,
newspaper, cardboard or anything that may restrict
airflow into the unit.
4. Do not install near external heat sources such as
radiators, heat registers, boilers or any device that
produces heat such as amplifiers or computers and
do not place near sources of naked flame.
5. Unplug apparatus from power supply during
lightening storms or when unused for long periods
of time.
6. Protect the power cable from being walked on,
pinched or restricted in any way, especially at plug
connections.
7. Only use attachments/accessories specified by the
manufacturer.
8. Units contain non-servicable parts - Refer all
servicing to qualified service personnel.
WARNING
To reduce the risk of fire, electric shock
or product damage:
4
Technical Support: [email protected] US: +866 677 0053 EU: +44 (0) 1793 230 343
FEA
TU
R
E
S AN
D SAFETY PR
E
C
A
UTI
ON
S
MX0404-QI
• Quick and easy installation – set up in seconds straight out of
the box.
• Simplified ports - Input: HDMI – Output: integrated RJ45
connectors for a single Cat5e/6/7 UTP cable to each display
point for ease of installation.
• Conforms to IEEE-568B standards
• Each HDMI port also supports DVI signals.
• Each Output port can be fed to multiple displays (cascaded).
• Enables up to 4 HDMI video/audio devices to be independently
switched through up to 4 HDMI displays or projectors for
uncompressed digital distribution.
• Each output able to show any connected source simultaneously
regardless of whether the input carries HDCP encryption.
• Refined for Custom Install and Home Theatre Installations.
• Reads and copies EDID from connected devices with additional
EDID configuration through customisable DIP switch settings if
necessary.
• 2k resolution supported.
• Fully 3D compatible – Frame sequential 3D (Blu-ray) and
interlaced stereoscopic 3D (satellite broadcasts etc.)
• Supports all high definition resolutions up to and including
1080p and standard video formats.
• RS232 port.
• Choose from 6 switching modes – infrared remote control, front
panel buttons, local IR, IR call-back, LAN and RS232.
• Simple switching remote control included, which can also be
learned into a universal remote handset to allow the control of
multiple devices from one handset.
• Fully compatible for integration with market leading control systems.
• 4 x IR 3.5mm mini-jack ports for each output to link IR from
control system to control display
• Additional infrared extension port for longer IR connections
• HDMI v.1.3
• Supports 24Bit Colour depth
• Signalling rate of 6.75 Gbps
• Pack comes complete with 1 x 4x4 Matrix with 19” rack
brackets, 4 x 40m IR receivers with mounting brackets, IR
receivers, emitters and a Matrix remote control handset.
Additional features included on the RX-1UTP-IR-40
• Transmits one-way signal together with the HDMI signal over a
single Cat5e/6/7 cable.
• Receivers capable of 1080p transmissions up to 40m (131ft)
under ideal conditions*
• For even greater control and fine tuning, each receiver features
a fully adjustable EQ distance range for optimising the
transmission signal.
2. Features
3. Safety Precautions
1. Do not expose this apparatus to rain, moisture, sprays,
drips or splashes and ensure that no objects containing
liquids are placed on the apparatus, including cups,
glasses and vases.
2. Do not place this unit in a confined space such as
enclosed shelving, cabinets or bookshelves. Ensure the
unit is adequately ventilated.
3. To prevent the risk of electric shock or fire hazard due to
overheating, do not cover the unit or obstruct ventilation
openings with material, newspaper, cardboard or
anything that may restrict airflow into the unit.
4. Do not install near external heat sources such as
radiators, heat registers, boilers or any device that
produces heat such as amplifiers or computers and do
not place near sources of naked flame.
5. Unplug apparatus from power supply during lightening
storms or when unused for long periods of time.
6. Protect the power cable from being walked on, pinched
or restricted in any way, especially at plug connections.
7. Only use attachments/accessories specified by the
manufacturer.
8. Units contain non-servicable parts - Refer all servicing to
qualified service personnel.
WARNING
To reduce the risk of fire, electric shock
or product damage:
• Protection against ESD (electrostatic discharge) included within
the unit to further stabilise transmission.
• LED indications for clear power and video signal selection.
• 5v mains supply included but receivers may be powered through the
USB port of the display using Wyrestorm USB to 5v power adaptor)
• Fully cascadable to further lengthen transmission.
*NOTE: ideal conditions denote cable run is within
specified distance range of product, no electrical
interference, the use of straight cable runs with no bends
or kinks and no patch panels or wall outlets used. Please
be advised that the presence of any of these factors in
your installation may compromise bandwidth and signal
strength. For longer transmission distances, RS232 control
and Ethernet pass-through, please see our full HDBaseT
or HDBT Lite range of matrices, transmitters, receivers and
extender sets.
USB to 5V Cable
Part Number
CAB-USB-5V
