background image

Introduction

Page 4 

February 2016

SCR-UM-00364-EN-02

General Safety

• 

Only trained competent persons shall operate the screed� An untrained operator is not 

qualified to operate the machine�

• 

Have a first aid kit available, and know how to use it�

• 

Have a fire extinguisher available, and know how to use it�

• 

Wear appropriate protective gear� This list includes but is not limited to:
◊ 

A hard hat

◊ 

Protective boots with slip-resistant soles

◊ 

Protective goggles

◊ 

Heavy gloves

◊ 

Hearing protection

• 

Stop engine, disconnect spark plug wire and wait for all moving parts to stop before 

servicing, adjusting, repairing or cleaning�

• 

Wear appropriate hearing protection when operating for long periods of time�

• 

Review safety related items with all personnel annually�

Operating safety

• 

Read and understand the operators manual and all safety signs before operating, 

servicing, adjusting or cleaning the screed�

• 

Clear the area of all bystanders before starting�

• 

Keep hands, feet, hair and clothing away from moving parts�

• 

Stay away from hot engine components during operation�

• 

Do not run the screed in an explosive atmosphere, a poorly ventilated or 

enclosed area�

• 

Do not smoke when refueling the gas engine�

Storage safety

• 

Store the unit in an area away from human activity�

• 

Do not permit children to play around the stored screed�

Refueling Safety

• 

Handle the fuel with care� It is highly flammable�

• 

This is a four cycle engine, use non-mixed gasoline of no less than 87 octane� 

• 

Allow the engine to cool for 5 minutes before refueling� Clean up spilled fuel before 

restarting the engine�

• 

Do not refuel the machine while smoking or when near open flame or sparks�

• 

Always use an approved fuel container�

• 

Fill the fuel tank outdoors�

• 

Prevent fires by keeping the machine clean of accumulated trash, grease and debris�

INTRODUCTION

Содержание screed king













Отзывы: