11
Tool Specifications
Machine Elements
1
ON/OFF-switch
2
Lower blade guard
3
Stop rail, right-hand side
4
Mitre lever
5
Mitre latch
6
Mitre scale
7
Rotating table/mitre arm
8
Stop rail, left-hand side
9
Bench mounting holes
10
Base
11
Base stabiliser
12
Bevel clamp handle
13
Bevel stop screw
14
Release lever for bevel angle stop
15
Socket wrench
16
Traverse bars
17
Sawdust ejector/connection for dust extraction
18
Transport safety
19
Transport handle
20
Adjusting screws for guide-rod clearance
21
Locking screw for guide rods
22
Adjusting screw for depth stop
23
Depth stop
24
Locking screws for stop rail
25
Recess
26
Blade slot
27
Spindle lock
28
Head lock up release lever
29
Carrying handle
Not all of the accessories illustrated or described are included as standard delivery.
Symbols and Meaning
Protective insulation, protection class II
CAUTION: Danger area, “Hands off”
CAUTION: Danger area, danger of injury through the unpro-
tected saw blade
Note for adjustment of the bearing play
Intended Use
The machine is intended for sawing of panels, profiles, wooden laths and
strips, as well as plastics or composite wood materials when using suitable
saw blades. The machine is not suitable for sawing of metal or non-ferrous
alloys.
The user is responsible for damage caused by usage other than intended for.
Scope of Delivery
The package contains:
– 1 Partly assembled machine
– 1 Socket wrench
– 1 Base stabiliser
– 1 Instruction manual
Assembly
Loosening the Transport Safety (see Fig. C)
Press the saw head slightly downward and pull out the pin of the transport
safety
18
. Move the saw head upward to the starting position.
Mounting the Frame Support (see Fig. D)
Insert the frame support
11
into the two supporting bores
31
. Mount the
frame support in such a manner that it rests on the supporting surface.
Tighten the screws
30
. For better handling during transport, the frame
support can be slid in.
Bench Mounting
To ensure secure handling, the machine must be mounted on a suitable
support (e. g. work bench, wooden table, etc.). When mounting the ma-
chine, ensure that the workbench is standing securely.
Depending on the application, the machine can be mounted stationary or
flexible, e.g. on a Würth saw table (accessory).
The supporting points of the machine are fitted with four bores
9
(see Fig.
A
). Insert the fitting bolts into the bores and fasten the machine
with the corresponding nuts and washers from the bottom side.
Inserting/Replacing Saw Blades
Before any work on the machine itself, pull the plug from the
socket!
The teeth of the saw blade are very sharp and can lead to inju-
ries. Wear protective gloves when inserting or replacing the
saw blade!
Never press the spindle lock 27 while the blade is rotating.
Use only saw blades where the maximum allowable speed is at
least as high as the no load speed of the machine.
Use only saw blades that are authorized by Würth and corre-
spond with the EN 847-1 Standard.
Use saw blades that correspond to the material to be cut.
HSS saw blades (high-speed steel) may not be used.
Loosen the screw
32
and tilt the saw blade guard
34
upward.
Press the spindle lock
27
and rotate the blade by hand until you feel the
lock engage. Continue to hold the spindle lock in to keep the blade from
turning (see Fig.
F
).
Using the socket wrench, loosen the blade bolt
33
by turning
clockwise (!)
.
Remove the blade bolt
33
, its washer and the outer flange
35
(see Fig.
E
).
Press the release lever
28
, move the bottom saw blade guard upward and
remove the saw blade
36
.
Install the new saw blade
36
onto the shoulder provided on the inner
flange making sure that the teeth at the bottom edge of the blade are
pointing towards the fence
3
/
8
(away from the operator).
Tighten the blade bolt
33
by turning
counter-clockwise (!)
while holding
the spindle lock
27
engaged with your other hand.
Cross-cut Mitre Saw
PS 350
Article number
0701 315 X
Power consumption
1600 W
Output power
800 W
No-load speed
4000 rpm
Mounting bore of the saw blade
30 mm
Saw blade dia. (max.)
305 mm
Mitre angle, right/left (max.)
60°/50°
Bevel angle, right/left (max.)
48°
Cutting depth x cutting width (max.)
- cross-cut, 90°
- mitre, 45°, bevel, 0° (left)
- mitre, 90°, bevel, 45° (left)
- mitre, 90°, bevel, 45° (right)
91 x 305 mm
91 x 216 mm
64 x 305 mm
43 x 305 mm
Dimensions
660 x 589 x 871 mm
Weight (without accessories)
27.0 kg
Protection class
/
II
PS 350 - GB Seite 11 Dienstag, 3. Februar 2004 1:17 13
Schwarz Prozeß 45,0° 169,71 LPI
