background image

 

 

Z=4

NFOV                                        Z=8

NFOV & 2× electronic zoom

 

Fig 7-2   

4. Focus Adjustment   

e, manual focus adjustment is necessary after starting up. Generally, 

. Polarity 

 

larity mode, higher brightness indicates higher temperature,. In negative polarity mode, 

ress “P” to invert. If current mode is positive polarity, press “P” to change into 

In order to get clear imag

NFOV is sensitive to focus adjustment. So, switch camera to NFOV firstly. After getting correct 

focus, then switch it to WFOV. The image quality should be the same for the same target. Focus 

adjustment method: Press “SHIFT” for 3 seconds until red part in keyboard get bright; then 

release “SHIFT”; Keep pressing “SHIFT” and then “F” to adjust far focus, keep  pressing 

“SHIFT” and then “N” to adjust nearfocus. If keeping pressing “SHIFT” & “F” or “SHIFT” & “N”, 

IR136 

Thermal Camera

 

will adjust far or near focus continuously. Information bar on bottom of 

image will display “FAR” or “NEAR” to indicate current focusing operation. 

 

5

In positive po

lower brightness indicates higher temperature,. Fig. 7-3 shows image effect of same target with 

different polarities.   

Operation method: P

negative polarity.   

 

 

17 

Содержание IR136

























Отзывы: