WSTECH BAT 0280-ES-1-400-1 Series Скачать руководство пользователя страница 29

Страница: 29 / 69

Original Operating Instructions
BATx0280-ES-1-400-1 (Outdoor)
Installation

O_BATx0280-ES-1-400-1_(Outdoor)_V1.3_GB

Page

3.5

Connections

DANGER!

Danger to life due to electric shock!

An incorrect selection and cable routing can cause damage to
property or serious injury or death to persons.

•

Wear suitable personal protective equipment for all work on the

product.

•

Selection and installation of electrical equipment, cables and

lines must comply to applicable local regulations and
standards.

•

Ensure that the diameter of the cables and lines matches the

diameters of the cable glands and connections.

•

Comply with the specified bend radii.

•

Offload the cables on both ends to relieve from pull and

pressure.

•

Route only one cable through each gland.

NOTICE

Damage of protection device!

All parameter changes to protection devices can cause damage.

•

Do not change the parameters of protection devices without

approval of the manufacturer.

•

Execute a trip test on the AC circuit breaker before

commissioning the product.

Cable requirements:

•

Compression cable lugs according to local regulations and standards.

•

Minimum degree of protection IP20

•

Cable entry grommets for AC connections and DC connections:

Minimum

: Ø 22 mm

Maximum

: Ø 36 mm

•

Parameters for cable sizing can be seen in Table 10.

Содержание BAT 0280-ES-1-400-1 Series






































































Результаты поиска

Содержание BAT 0280-ES-1-400-1 Series

Отзывы:

Похожие инструкции для BAT 0280-ES-1-400-1 Series

Бренды по названию

Популярные бренды

WSTECH BAT 0280-ES-1-400-1 Series, Руководство по эксплуатации

Результаты поиска

Содержание BAT 0280-ES-1-400-1 Series

Отзывы:

Похожие инструкции для BAT 0280-ES-1-400-1 Series

Бренды по названию

Популярные бренды