background image

 

WSG-HY128 Interface Card / User Guide

 

 

Compliance Information 

FCC INFORMATION (U.S.A.) 

 

IMPORTANT

 

NOTICE:

 

DO

 

NOT

 

MODIFY

 

THIS

 

UNIT! 

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. 
Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

 

 

Important: 

When connecting this product to accessories and/ or another product use only high-quality shielded cables. Cable/s 
supplied with this product MUST be used. 
Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the 
USA.

 

 

Note: 

This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” 
digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product 
in a residential environment will not result in harmful interference with other electronic devices. This equipment 
generates/uses radio frequencies and, if not installed and used according to the instructions found in the user manual, may 
cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not 
guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which 
can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following 
measures: This device complies with Part 15 of the FCC Rules. 

Operation is subject to the following two conditions: 

a.

  This device may not cause harmful interference. 

b.

  This device must accept any interference received including interference that may cause 

undesired operation.

 

 

See user manual instructions if interference to radio reception is suspected. 

 

Содержание HY-128



















Отзывы: