10
PRODUCT WATER FAUCET SITE PREPARATION
Refer to Faucet Installation Instructions (Page 6) for site location and mounting hole specifications.
Primary considerations for site selection are convenience of use and an open area under sink. An existing 7/8”
Sink Hole will also accommodate metal faucets with air-gap connections. Always check underside of selected
location for obstructions.
PORCELAIN/ENAMEL OVER STEEL
OR CAST IRON SINKS
1.
CAUTION:
A heavy duty, variable speed drill motor
with a spring-loaded porcelain drill set (Figure 6) is
strongly recommended for this procedure.
CAUTION:
The plastic sleeve supplied on pilot drill
(Figure 6.A) is to be positioned on drill bit against drill
chuck. This prevents chuck from contacting
porcelain after pilot hole has been completed.
NOTE:
Practice on discarded sinks to familiarize
yourself with operation of porcelain cutter kit.
Using carbide tipped bit with plastic sleeve (Figure
6.A.), drill pilot hole completely through porcelain and
metal underneath.
2.
CAUTION:
Avoid high motor R.P.M. during initial
penetration of porcelain, as high drill speed will cause
excessive chipping.
Place spring-loaded porcelain saw (Figure 6.B.) into
drill chuck. Make sure pilot guide is inserted tightly.
Insert pilot guide into pilot hole. Push down gently on
drill motor to apply light pressure to porcelain surface.
Start drill motor turning as slowly as possible.
After initial cut has started, motor speed may be
gradually increased. The cut may require three to
four minutes to complete. Going faster could result in
excessive chipping. Be sure a complete ring has
been cut through porcelain to material underneath.
3. Place finish hole saw (Figure 6.C.) into drill chuck.
Make sure pilot guide is inserted tightly. Insert pilot
guide into pilot hole. Begin cut using a slow speed
and light pressure until porcelain (inside ring cut in
Step 2) has been penetrated to material underneath.
4. Remove saw from hole and clean all debris from
porcelain surface. Re-insert saw into hole and cut
through remaining material.
5. Installation hole is ready, install faucet.
TILE COUNTER TOP
1. Follow procedures detailed in section labeled
"Porcelain/Enamel Over Steel" (substitute "tile" for
"Porcelain" in instructions).
STAINLESS STEEL SINK
1. Use a center punch to make a small indentation to
mark center of desired location.
2. Drill a pilot hole with a 1/8" metal drill bit, then enlarge
hole with a 9/16" metal drill bit.
3. Complete hole size by using a 1 1/4" chassis punch.
4. Installation hole is ready, install faucet.
A. PILOT DRILL
B. SPRING LOADED PORCELAIN SAW
C. FINISH HOLE SAW
Figure 6
INSTALLATION STEPS CONT’D
PRODUCT WATER FAUCET SITE PREPARATION
Primary considerations for site selection are convenience of use and an open area under sink. An existing 7/8” sink
hole will also accommodate metal faucets with air-gap connections. Always check underside of selected location for
obstructions.
PORCELAIN/ENAMEL OVER STEEL OR CAST IRON
SINKS
1.
CAUTION:
A heavy duty, variable speed drill motor with
a spring-loaded porcelain drill set (Figure 6) is strongly
recommended for this procedure.
CAUTION:
The plastic sleeve supplied on pilot drill
(Figure 6.A) is to be positioned on drill bit against drill
chuck. This prevents chuck from contacting porcelain
after pilot hole has been completed.
NOTE:
Practice on discarded sinks to familiarize
yourself with operation of porcelain cutter kit.
Using carbide tipped bit with plastic sleeve (Figure 6.A.),
drill pilot hole completely through porcelain and metal
underneath.
2.
CAUTION:
Avoid high motor R.P.M. during initial
penetration of porcelain, as high drill speed will cause
excessive chipping.
Place spring-loaded porcelain saw (Figure 6.B.) into drill
chuck. Make sure pilot guide is inserted tightly. Insert
pilot guide into pilot hole. Push down gently on drill
motor to apply light pressure to porcelain surface. Start
drill motor turning as slowly as possible.
After initial cut has started, motor speed may be
gradually increased. The cut may require three to
four minutes to complete. Going faster could result in
excessive chipping. Be sure a complete ring has been
cut through porcelain to material underneath.
3. Place finish hole saw (Figure 6.C.) into drill chuck. Make
sure pilot guide is inserted tightly. Insert pilot guide
into pilot hole. Begin cut using a slow speed and light
pressure until porcelain (inside ring cut in Step 2) has
been penetrated to material underneath.
4. Remove saw from hole and clean all debris from
porcelain surface. Re-insert saw into hole and cut
through remaining material.
5. Installation hole is ready, install faucet.
TILE COUNTER TOP
1. Follow procedures detailed in section labeled “Porcelain/
Enamel Over Steel” (substitute “tile” for “Porcelain” in
instructions).
STAINLESS STEEL SINK
1. Use a center punch to make a small indentation to mark
center of desired location.
2. Drill a pilot hole with a 1/8” metal drill bit, then enlarge
hole with a 9/16” metal drill bit.
3. Complete hole size by using a 7/8” chassis punch.
4. Installation hole is ready, install faucet.
Содержание WaterSTATION PuR100-7
Страница 1: ...92673 Rev 1 11 PuR100 7 Installation Operation Service Record and Warranty...
Страница 28: ......
