Woxcon IPA300TR Скачать руководство пользователя страница 8

Страница: 8 / 58

4K IP Streaming Extender

1.2 Features

BlueRiver™ NT+ technology. Flexible used as either transmitter or receiver.

Streams uncompressed video with zero-latency, audio, and control, with the

flexibility of transmitting them together or to separate network destinations.

Supports HDMI input and output video resolution up to 4K@60Hz 4:4:4 8bit,

1080P 3D.

18Gbps high bandwidth and supports HDR 10 and Dolby Vision.

Transports RS232 and IR signal to any units by using Unicast or Broadcast IPV4

protocol or local control by API server.

IPA300TR/ IPA300TR-P series are configurable HDCP 2.2 compliant.

Supports arbitrary Multi-view layout.

Supports Video Wall mode up to 5x5 screens.

Selectable output resolutions up to 4K scaling ability.

Transmitter route HDMI audio, external audio as an independent streaming for

receiver embedding.

BlueRiver NT+ Series is compatible with SDVoE, offering zero-latency AV-over-IP

with true 4K@60 and video processing.

IPA300TR-P supports video preview on the IPA manager software, while

IPA300TR can’t.

1.3 Package List

IPA300TR/ IPA300TR-P:

1x IPA300TR/ IPA300TR-P

2x Mounting Ears with 2 Screws

4x Plastic Cushion

1x 3-pin Terminal Block

1x User Manual

Note:

Please contact your distributor immediately if any damage or defect in the

components is found.

Содержание IPA300TR


























































Результаты поиска

Содержание IPA300TR

Отзывы:

Похожие инструкции для IPA300TR

Бренды по названию

Популярные бренды

Woxcon IPA300TR, Руководство пользователя

Результаты поиска

Содержание IPA300TR

Отзывы:

Похожие инструкции для IPA300TR

Бренды по названию

Популярные бренды