Worx WXI 4CSA Скачать руководство пользователя страница 9

Circular saw                                       WX14CSA

OPERATING INSTRUCTIONS

1. SAFETY ON/OFF SWITCH

Your switch is locked off to prevent accidental starting. 

Depress lock off button (8) then on/off switch (1) and 

release lock off button (8). Your switch is now on. To 

switch off just release the on/off switch.

2. HAND GRIP POSITION

Always hold your saw firmly with both hands when 

operating. The right and wrong ways to support large 

workpieces are shown in Figures A and B.

3. FITTING AND CHANGING A SAW BLADE

Warning: Your circular saw has been 

shipped completely assembled, except for 

the blade, which is packed unassembled. Before 

fitting you must inspect the saw blade carefully 

to make sure that no breakage or damage has 

occurred during shipping.

Press the spindle lock button (9), and use the hex key 

(12) provided to remove the blade bolt (15) and outer 

flange (16). Rotate lower blade guard (4) clockwise and 

hold open using the lower blade guard lever (5) whilst 

changing the saw blade (6). Ensure the blade bore is 

located on the inner flange (14) and the blade direction 

arrow points in the same direction as the lower blade 

guard (4) arrow. Check the blade surface and flanges 

are clean. Press the spindle lock (9) again and re-fit 

the outer flange (16) over spindle (17) flat and tighten 

the bolt with 1/4 turn more than finger tight. Check the 

blade is securely clamped.

Warning: Blade teeth are very sharp.

For best cutting results ensure you use a saw 

blade suited to the material and cut quality you need.

4. DEPTH OF CUT ADJUSTMENT

Lift the depth of cut locking lever (10) and raise the saw 

body away from the base plate (3). Set the depth of cut 

using the scale (11) and push the lever (10) down to lock 

(See C and D). Always add 3mm to your depth of cut so 
the blade can cut through the material.

5. BASE PLATE

Adjusting the angle of the base plate (3) enables bevel 
cutting (See E). The base plate (3) must always be held 
firmly against the material being cut to reduce saw 
vibration, blade jumping or blade breakage (See F).

6. BASE PLATE ANGLE ADJUSTMENT

Loosen two base plate bevel lock knobs (7) and rotate 
the base plate (3) to set the bevel angle using the base 
plate angle scale (18) provided. Then clamp the base 

A

B

C

D

WRONG

RIGHT

RAISE

LOWER

ENG-WX14CSA-M-061227.indd   9

2007-1-5   13:39:18

Содержание WXI 4CSA

















Отзывы: