Worx WG368E Скачать руководство пользователя страница 21

Страница: 21 / 24

Cordless Chain Saw WG368E WG368E.9

TROUbLEShOOTING

Symptom

Possible causes

Possible Solution

Chain saw fails to
operate

Out of battery
Fuse faulty

Charge the battery pack
Replace fuse

Chain saw operates
intermittently

Loose connection
Internal wiring defective
On/Off switch defective

Contact service agent
Contact service agent
Contact service agent

Dry chain

No oil in reservoir
Vent in oil filler cap clogged
Oil passage clogged

Refill oil
Clean cap
Clean oil passage outlet

Kickback Brake / Run
down brake

Brake does not stop chain

Contact service agent

Chain/chain bar
overheats

No oil in reservoir
Vent in oil filler cap clogged
Oil passage clogged
Chain is over tensioned
Dull chain

Refill oil
Clean cap
Clean oil passage outlet
Adjust locking knob
Sharpen chain or replace

Chain saw rips, vibrates,
does not saw properly

Chain tension too loose
Dull chain
Chain worn out
Chain teeth are facing in the
wrong direction

Adjust locking knob
Sharpen chain or replace
Replace chain
Reassemble with chain in correct
direction

Never use tools with defective On/Off switches or defective Kickback brake(Hand Guard).
In the case of all other types of technical faults, please contact helpline or local service center.

Содержание WG368E
























Результаты поиска

Содержание WG368E

Отзывы:

Бренды по названию

Популярные бренды

Worx WG368E, Инструкция по безопасности и эксплуатации

Результаты поиска

Содержание WG368E

Отзывы:

Бренды по названию

Популярные бренды