Worx WG150E, Руководство пользователя, Страница: 12 / 16

Cordless Grass Trimmer ENG
13 12 13 12
sure motor is up to full speed before
trimming.
WARNING: Use only 1.2mm cutting
line. diameter line. Other sizes of
line will not feed properly and will result
in improper cutting head function or can
cause serious injury. Do not use other
material such as wire, string, rope, etc.
Wire can break off during cutting and
become a dangerous missile that can
cause serious injury.
Trimming
Hold the bottom of the trimmer head about
8 cm above the ground and at an angle. Allow
only the tip of line to make contact. Do not
force trimmer line into work area.
Edging(See Fig K)
Unscrew the upper locking knob (3) and rotate
the main and auxiliary handle to 90
o
with
cutting head (See Fig 8).
Retighten the upper locking knob.
Adjust trimmer head angle to be the lowest
horizontal setting. Then position the wheel on
the ground for edge mode. The guard has two
white line guides to indicate the cutting line
position. Align these marks with the edge of
your lawn.
While edging allow the tip of the line to make
contact. Do not force the line. The rotation
wheel helps protect the unit and keeps the unit
from contacting the ground. Take extra caution
while edging as objects can be thrown from
the trimmer line.
AUTOMATIC LINE FEED SYSTEM
When initially switching on the trimmer, a small
length of line is fed out.
A ‘clattering’ noise will be heard when the lines
hit the line cutter.
DO NOT BE ALARMED
this
is quit normal. After about 5 seconds the line
will be cut to the correct length and the noise
will reduce as the motor receives full speed.
If the noise of the line being cut can’t be heard,
more line will be fed out.
To feed more line, it is first necessary to allow
the trimmer to stop completely, then restart,
allowing the motor to reach full speed.
Repeat above 4 until you hear the lines hitting
against the line cutter. (Do not repeat this
procedure more than 6 times)
TO MANUALLY FEED THE LINE (SEE FIG L)
If required line can be feed out manually
To operate, press and release manual line feed
button (16), whilst gently pull out the lines until
the lines reach the line cutter.
When the required amount of line is fed out,
gently pull on the second line (there is no need
to press the manual line feed button again)
If the line extends past the line cutter, too much
line has been fed out.
If too much line is fed out, remove the spool
cap and click spool anti-clockwise until the line
is at the desired length.
TO REMOVE THE CAP
Press and hold in the two latches (12) (See Fig
M).
Pull cap away from the spool holder
When refitting the spool cap.
Keep all areas of the cap and spool holder
clean.
Replace the cap, pressing firmly down towards
the spool holder to ensure cap is fully located.
Check that the cap is correctly fitted by trying to
remove it without depressing the two latches.
TO REPLACE CUT LINE
For your convenience it is recommended you
buy spool and line complete.
To fit spool and line complete:
Remove old spool.
Place new spool into cap with cut out areas of
the spool in line with eyelets.
Release line from cleat and feed line through
eyelet .
Refit the cap.
To fit nylon line only:
WARNING!
Take approximately 6m of
line. Insert 10mm of line into the spool
holes and wind line in the direction of the
arrows on the top of the spool.
Your Trimmer is designed to use only line with
a
maximum diameter of 1.2mm
IMPORTANT:
Leave approximately 100mm of
line unwound and place into cleat.
Care should be taken to ensure that the line
is neatly coiled on the spool. Failure to do so
will impair the efficiency of the automatic line
feed.
Then fit spool as described in
“To fit spool
and line complete”.
CRA-WG150E-M-061102.indd 12 2007-3-28 17:11:06