Worx WG124, Руководство пользователя, Страница: 10 / 28

6.0 AMP Electric Grass Trimmer/Edger EN
10
ASSEMBLY
1. ASSEMBLY OF THE SAFETY GUARD (SEE
FIG A)
Remove the screw from the Safety Guard (6) and fit
the guard to the trimmer head; align the guard so it
slides into the slots located on the trimmer head. Turn
the tool over and secure the Safety Guard onto the
trimmer head with the screw (a) provided.
2. ASSEMBLY OF THE EDGER WHEEL (SEE FIG B)
With the tool right side up, slide the Edger Wheel
assembly onto the metal plate located on the side
of the trimmer head. Make sure the grooves of the
Edger Wheel assembly locks onto the metal plate; you
will hear it click into place.
To remove the wheel assembly, press the release
button (b) on the wheel and pull the wheel assembly
upward.
OPERATING INSTRUCTIONS
Warning: The cutting head continues
to rotate after the trimmer has been
switched off. Wait until it stops before laying
the trimmer down.
● Always wear eye protection. Never lean
over the trimmer head. Rocks or debris can
ricochet or be thrown into the eyes and
face and cause blindness or other serious
injury.
● Hold front handle with one hand and
auxiliary handle with the other hand. Keep
unit below waist level. Work only from
your right to your left to ensure debris is
thrown away from you. Without bending
over, keep line near and parallel to the
ground (perpendicular when edging) and
not crowded into material being cut.
● Before operating, make sure both trimmer
lines are extended. When trimming, make
sure motor is running at full speed.
● Use only 0.065”(1.65mm) diameter cutting
line. Other line sizes will not properly
feed in the trimmer head and could cause
serious injury. Never use other materials
such as wires, string or rope, as this may
break off during cutting and cause serious
injury.
1. FLOWER GUARD
Push the Flower Guard (7) in when edging and pull
it out before trimming, as shown in Fig C. Before
trimming or edging make sure the Flower Guard is
locked firmly in position.
2. ADJUSTMENT OF THE TELESCOPIC SHAFT
(SEE FIG. D)
Unscrew the Locking Collar (5) clockwise to unlock, as
indicated. Adjust the length of the Telescopic Shaft (8)
to the most comfortable length. Tighten the Locking
Collar counter-clockwise to lock, as indicated.
3. MAIN HANDLE ROTATION
First, hold down the lower housing with your foot and
pull upward on the Telescopic Shaft (8). Then rotate
the Telescopic Shaft clockwise 90 degrees (See Fig.
E1) and release; the Shaft will be locked in position
automatically (See Fig. E2).
4. ADJUSTING THE AUXILIARY HANDLE (SEE
FIG. F)
Pull up the Auxiliary Handle Locking Lever (12).
Hold the lever and rotate the Auxiliary Handle (9) to
the most comfortable and balanced position (See Fig
F).
Release the lever, your Auxiliary Handle has been
locked.
5. ATTACHING EXTENSION CORD (SEE FIG G)
An extension cord retainer is built into the Rear
Handle that prevents the cord from coming
unplugged. To use this feature, simply double the
extension cord about 8 inches (203mm) from the end,
forming a small loop. Insert this loop into the slot
on the back of the handle. Hook the end of the loop
over the tab. Gently tug on the cord to insure that it
is firmly retained in the trimmer’s handle. Plug the
receptacle end of the extension cord into the Plug
Insert (4) in the trimmer.
6. ADJUSTMENT OF TRIMMER HEAD ANGLE
To adjust the trimmer head angle downwards, put
one foot on the motor housing, then grip the Rear
and Auxiliary handles, and apply adequate force to
adjust, as shown in Fig. H1.
To adjust the trimmer head angle upwards, put one
foot on the Safety Guard, then grip the Rear and
Auxiliary handles and apply adequate force to adjust,
as shown in Fig. H2.
7. USING THE ON/OFF SWITCH (SEE FIG. I)
Press and hold the on/off switch (2) to start the
trimmer. Release to stop.
8. TRIMMING
Hold the bottom of the trimmer head just above the
ground and at a slight angle. Allow only the tip of line
to make contact with the grass. Let the trimmer line
work at its own pace; do not force the trimmer line
into the work area.
9. EDGING (SEE FIG J)
First, rotate the Rear Handle 90 degree clockwise (See
“Main Handle Rotation”, Fig. E1 & E2 ).
Adjust the trimmer head angle to be the lowest
horizontal setting (See “Adjustment of the Trimmer
Head Angle”, Fig H1). Then position the Edger Wheel
on the ground for edge mode (See Fig. J). There are
two white lines, located on each end of the Safety
Guard, that show the cutting plane of the trimmer
line. Align these marks with the edge of your lawn.
While edging, allow the tip of the line to make
contact. Do not force the line. The wheel helps to