Worx Nitro, Руководство пользователя

Страница: 10 / 130

10
Cordless Chainsaw EN
2) CAUSES AND OPERATOR
PREVENTION OF KICKBACK:
Kickback may occur when the nose or tip of the guide
bar touches an object, or when the wood closes in and
pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden reverse
reaction, kicking the guide bar up and back
towards the operator.
Pinching the saw chain along the top of the guide bar may
push the guide bar rapidly back towards the
operator.
Either of these reactions may cause you to lose control of
the saw which could result in serious personal
injury. Do not rely exclusively upon the safety devices
built into your saw. As a chain saw user, you should take
several steps to keep your cutting jobs free from accident
or injury.
Kickback is the result of chain saw misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given below:
a) Maintain a firm grip, with thumbs and fingers
encircling the chain saw handles, with both
hands on the saw and position your body and arm
to allow you to resist kickback forces. Kickback
forces can be controlled by the operator, if proper
precautions are taken. Do not let go of the chain saw.
b) Do not overreach and do not cut above shoulder
height. This helps prevent unintended tip contact and
enables better control of the chain saw in unexpected
situations.
c) Only use replacement bars and chains specified
by the manufacturer. Incorrect replacement guide
bars and saw chains may cause chain breakage and/or
kickback.
d) Follow the manufacturer’s sharpening and
maintenance instructions for the saw chain.
Decreasing the depth gauge height can lead to
increased kickback.
Residual risks
Even with the intended use of the appliance there is
always a residual risk, which can not prevented. According
to the type and construction of the appliance the
following potential hazards might apply:
- Contact with exposed saw teeth of the saw chain
(cutting hazards)
- Access to the rotating saw chain (cutting hazards)
- Unforeseen, abrupt movement of the guide bar
(cutting hazards)
- Flung out of parts from the saw chain (Cutting /
injection hazards)
- Flung out of parts of the work piece
- Skin contact with the oil
- Loss of hearing, if no required ear protection used
during work
SAFETY WARNINGS FOR BAT-
TERY PACK
a) Do not dismantle, open or shred cells or battery
pack.
b) Do not short-circuit a battery pack. Do not store
battery packs haphazardly in a box or drawer
where they may short-circuit each other or be
short-circuited by conductive materials.
When
battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
c) Do not expose battery pack to heat or fire. Avoid
storage in direct sunlight.
d) Do not subject battery pack to mechanical shock.
e) In the event of battery leaking, do not allow the
liquid to come into contact with the skin or eyes.
If contact has been made, wash the affected area
with copious amounts of water and seek medical
advice.
f) Seek medical advice immediately if a cell or
battery pack has been swallowed.
g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with a clean dry
cloth if they become dirty.
i) Battery pack needs to be charged before use.
Always refer to this instruction and use the
correct charging procedure.
j) Do not maintain battery pack on charge when not
in use.
k) After extended periods of storage, it may
be necessary to charge and discharge the
battery pack several times to obtain maximum
performance.
l) Recharge only with the charger specified by
WorxNITRO. Do not use any charger other than
that specifically provided for use with the
equipment.
m) Do not use any battery pack which is not
designed for use with the equipment.
n) Keep battery pack out of the reach of children.
o) Retain the original product literature for future
reference.
p) Remove the battery from the equipment when
not in use.
q) Dispose of properly.
r) Do not mix cells of different manufacture,
capacity, size or type within a device.
s) Do not remove battery pack from its original
packaging until required for use.
t) Observe the plus (+) and minus (–) marks on the
battery and ensure correct use.
SAVE THESE INSTRUCTIONS
Instructions concerning the proper techniques for
basic felling, limbing, and cross-cutting
1. Felling a tree
When bucking and felling operations are being performed
by two or more persons at the same time, the felling