Worx Nitro WX102, Инструкция по безопасности и эксплуатации. Оригинальные инструкции.

Страница: 12 / 16

12
20V Cordless Drill Driver EN
The tightness of the grip on the handles and if any anti
vibration and noise accessories are used.
And the tool is being used as intended by its design and
these instructions.
8LMWXSSPQE]GEYWILERHEVQZMFVEXMSRW]RHVSQIMJMXW
use is not adequately managed.
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the
operating cycle such as the times when the tool is
switched off and when it is running idle but not actually
HSMRKXLINSF8LMWQE]WMKRMƼGERXP]VIHYGIXLII\TSWYVI
level over the total working period.
Helping to minimise your vibration and noise exposure
risk.
Always use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions
and keep well lubricated (where appropriate).
If the tool is to be used regularly then invest in anti
vibration and noise accessories.
Plan your work schedule to spread any high vibration tool
use across a number of days.
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
INTENDED USE:
The machine is intended for driving in and loosening
screws as well as for drilling in wood, metal and plastic.
ASSEMBLY AND OPERATION
ACTION FIGURE
BEFORE OPERATION
Checking the battery charge condition
NOTE: Fig. A1 only applies for the
battery pack with battery indicator light.
See Fig. A1
Removing the battery pack See Fig. A2
Charging the battery See Fig. A3
Installing the battery pack See Fig. A4
ASSEMBLY
CHUCK ADJUSTMENT
WARNING: Always lock off trigger switch and
disconnect tool from power source when
changing accessories. Always ensure the bit is secure
before starting the tool. Damage to the Chuck or a loose
FMXQE]GEYWITSWWMFPITIVWSREPMRNYV]
-- Removing the bits See Fig. B1
-- Inserting the bits See Fig. B2
-- Assembling the belt hook and bit clip
See Fig. C1,
C2, C3, C4
OPERATION
*SV[EVHVIZIVWIVSXEXMSRGSRXVSP
WARNING: Never change the
direction of rotation when the
chuck is rotating, wait until it has
stopped!
See Fig. D1,
D2, D3
8;374))(+)%6'328630
WARNING: To prevent gear
damage, always allow the chuck to
come to a complete stop before
changing the direction of rotation.
See Fig. E
TORQUE ADJUSTMENT
Drilling, Screw driving
See Fig F1,
F2
3TIVEXMRKXLI3R3JJW[MXGL
WARNING: Do not operate for long
periods at low speed because
excess heat will be produced internally.
See Fig G
LED light indicator
Before operation, the LED light will be
EGXMZEXIH[LIRXLI3R3JJW[MXGLMW
slightly depressed.
WARNING: To turn on the light,
TVIWWXLI3R3JJW[MXGLERHQEOI
WYVIXLI*SV[EVH6IZIVWI6SXEXMSR
'SRXVSPMWSRVMKLXPIJXTSWMXMSR
The tool and battery are equipped with a
protection system. When the LED Light
MWUYMGOP]ƽEWLMRKWIGSRHWERHXYVR
off, the system will automatically cut off
power to the tool to extend battery life.
The tool will automatically stop during
STIVEXMSRMJXLIXSSPERHSVFEXXIV]
are placed under one of the following
conditions:
• Overloaded: The tool is operated
in a manner that causes it to draw
an abnormally high current. In this
situation, release the Trigger Switch on
the tool and stop the application that
caused the tool to become overloaded.
Then pull the Trigger Switch again to
restart.
•
3ZIVLIEXIH
Under the condition
above, if the tool does not start, the
Tool and Battery are overheated. In this
situation, let the Tool and Battery cool
before pulling the Trigger Switch again.
• Low battery voltage: The remaining
Battery capacity is too low and the
tool will not operate. In this situation,
remove and recharge the Battery.
See Fig. G
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON WHEN YOU
PRESS THE SWITCH?
8LIJSV[EVHVIZIVWIVSXEXMSRGSRXVSP[LMGLMWSRXSTSJXLI
XVMKKIVMWTSWMXMSRIHMRXLIPSGOJYRGXMSR9RPSGOXLIJSV[EVH
reverse rotation control by putting it into the required rotation
position. Push the trigger and the drill will start to rotate.
Check that the battery is charged and properly connected
to the tool.