background image

Safety

14

 

− Batteries must not be charged, opened, thrown into fire, short circuited or 

reactivated by other means.

 

− Avoid contact with skin, eyes and mucus membranes. In the event of 

contact with battery acid, the affected area must be rinsed immediately 

with plenty of clean water and a doctor must be consulted immediately.

 

− If batteries are swallowed or if they are inside the body for any reason, 

seek medical advice immediately. Keep batteries away from children and 

animals.

 

− Take the batteries out of the battery compartment if they are empty or 

if you do not use the drill for a prolonged period of time. This avoids 

damage that could be caused by battery leakage.

 

− Do not expose the batteries to extreme conditions by, for example, placing 

them on radiators or exposing them to direct sunlight. 

 

− If necessary, clean the contacts of the batteries and device before 

inserting them, e.g. with a piece of emery cloth.

 

− Make sure that the polarity is correct when inserting the batteries.

 

− Do not use old and new batteries of different types.

Supplementary safety instructions

 

− The drill may only be used by adults. 

 

− Children must be supervised to make sure that they do not play with the 

drill.

 

− Keep children away from the packaging material and small parts. There is 

a choking hazard if swallowed.

 

− Only connect the drill if the mains voltage of the socket corresponds to the 

specification on the nameplate.

 

− Only connect the drill to an easily accessible socket so that you can quickly 

disconnect it from the mains in case of a failure.

 

− Do not operate the drill if it exhibits visible damages or the mains cord or 

mains plug is defective.

 

− If the mains cord for the drill is damaged, it must be replaced by the 

manufacturer, its After Sales Support department or a similarly qualified 

person in order to prevent risks.

Содержание WZ-TB 13 L


































Отзывы: