Worcraft AG2004B-125, Инструкция по эксплуатации

Страница: 53 / 69

e) Do not use chain or toothed saw blades. Such attachment
tools frequently cause a kickback or loss of control over the
electric tool.
Special safety instructions for grinding and cutting
a) Use only grinders which have been approved for your
electric tool and the protective hood intended
for these grinders
. Grinders which are not intended for the
electric tool may not be sufficiently shielded and are unsafe.
b) Depressed centre grinding wheels must be pre- mounted
in such a way that their grinding surface does not protrude
over the level of the edge of the protective cover.
An
incorrectly mounted grinding wheel which protrudes beyond the
level of the edge of the protective cover cannot be adequately
shielded.
c) The protective hood must be securely attached to the
electric tool and adjusted so that the greatest level of safety
is reached
, i.e., the smallest possible amount of the grinder is
exposed to the operator. The protective hood should protect the
operator from broken bits and accidental contact with the grinder.
d) Grinders may only be used for the recommended
attachment options.
For example: Never grind with the side
surface of a cutting disc. Cutting discs are for cutting material
using the edge of the disc. Pushing sideways on these grinders
can break them.
e) Always use undamaged clamping flanges of the correct
size and shape for the grinding disc you selected.
Suitable
flanges support the grinding disc and thus reduce the danger of
the grinding disc breaking. Flanges for cutting discs can be
distinguished from flanges for other grinding discs.
f) Do not use worn grinding discs for larger electric tools.
Grinding discs for larger electric tools are not set up for the higher
rotation speeds of smaller electric tools and can break.
Other special safety instructions for cutting grinding
a) Avoid blocking the cutting disc or pressing down too hard.
Do not make any excessively deep cuts. Overloading the cutting
disc increases wear and its tendency to tilt or block and, with that,
to kickback or break the grinder.
b) Avoid the area in front of and behind the rotating cutting
disc.
When you move the cutting disc by itself in the workpiece, in
the event that the electric tool kicks back with the rotating disc, it
can spin directly towards you.
c) If the cutting disc jams, or you interrupt your
work, switch the device off and hold it until the disc
has come to a full stop
. Never try to pull the cutting
disc out of the cut while it is still running, because it can
kick back. Identify and correct the cause of the jamming.
d) Do not switch the electric tool on again as long as
it is in the workpiece.
Allow the cutting disc to first
reach its full rotational speed before you carefully
resume with the cutting. Otherwise, the disc may catch,
spring away from the workpiece or cause a kickback.
e) Support plates or workpieces to reduce the risk of
kickback from a jammed cutting disc.
Large
workpieces may bend under their own weight. The
workpiece must be supported on both sides of the disc,
near the cutting disc as well as also at the edge.
f) Be particularly careful for pocketcuts in existing
walls or other areas where you cannot see what is
there.
The cutting disc may cause a kickback when it
cuts into gas or water lines, electrical lines or other
hidden objects.
Additional safety instructions for sanding
Special safety instructions for sanding:
•
Do not use overly large sandpaper sheets; follow
the manufacture
r‘s information for sandpaper sizes.
Sandpaper sheets which extend beyond the sanding
plate can cause injuries and can block, tear the
sandpaper, or cause kickback.
Additional safety instructions for working with wire
brushes
Special safety instructions for working with wire brushes:
•
Be aware that the wire brushes also lose wire
pieces during typical use. Do not overload the wires
by pressing down too hard.
Flying wire pieces can
very easily penetrate thin clothing and/or your skin.
•
If a protective hood is recommended, do not allow
the wire brushes and the protective hood to touch
each other.
The diameter of plate and cup brushes can
enlarge if too much pressure and centrifugal force is
exerted.
ASSEMBLY
／
OPERATION
WARNING! Before assembly or do any adjustment, please be
sure the battery pack already removed from the tool.
Mounting the wheel guard (Fig. 3)
1. Put the wheel guard onto the gear box, make sure the
protrude point aligned with the slot on the grear box. Then
move the guard anti-cloackwise till which is cross with the
tool body.
2. Press the locking button to lock the guarg on the position.
Note: Check the guard to make sure it is totally secured, if not
tighten enough, you can use a open-end spanner to fasten the nut
on the locking button.
Mounting the abrasive wheels (Fig.4)
1. Press down the spindle locking button and hold it.
2. Using the spanner to lossen the outer flange and remove it.
3. Put the abrasive wheel to the output spindle.
4. Put back the outer flange.
5. Press down the spindle lock button and hold it, meanwhile
using the spanner to fasten the outflange.
Mounting the auxiliary handle (Fig 5)
Align the handle with the thread hole on the tool head, and then
turn to fasten it.
Note: For comfortable of working on different operation positions,
the auxiliary handle can be mounted on the left or right
side of the gear box.
Mounting / Disassemble the battery pack (Fig. 6)
Align the battery pack slot with the battery foot on the
tool, and then push downward, until completely mounted.
To disassemble it, just keep pressing the red battery
pack knob and pull backward.
Switching on / off the tool (Fig. 7)
This tool is equipped with a safety lock-off switch.
To start the tool, using your finger to press down the rear
part of switch button and then push it forward, the grinder
will start. After that press the front part of switch trigger
down. The switch thus be locked on postion and the tool
will continuously start.
To switch off the tool, just press the rear part of the
switch button again, the switch will automatically comes
back to backward postion, the tool will stop.
Speed select (Fig. 8)
This tool designed with two speed optional.
The low speed(14) and high speed(15) LED indicator
equipped on the top of battery pack slider. You can
selector the speed as you desire via press the select