Woodstream 1440-655, Руководство по эксплуатации

Страница: 5 / 15

8
Instructions
Charge your battery per instructions on page 6. Under proper
usage, battery will last all season.
Starting Instructions
It is recommended that you read the entire manual before
starting the Mosquito Magnet
®
trap.
1. To start the trap, press and hold the ON/OFF button for
three seconds until the orange LED illuminates.
2. RUN will show on the display. WARM and the indicator
arrows will also flash on the display. The LED (indicator
above ON/OFF button) will be orange.
3. The fan will ramp from low speed to high speed after
approximately 3 minutes.
4. The display will flash WARM and the LED will be
orange for approximately 15-25 minutes while the trap
is warming up.
5. After the trap reaches operating temperature, the LED
will be green and WARM will disappear from the
display.
Shut Down Instructions
To turn off the trap, press the ON/OFF button. RUN will show on
the display. COOL and the indicator arrows will flash on the
display. The LED will be green. After a two minute cool down,
the fan will stop, the LED will turn off and OFF will show on the
display.
When Not In Use
If the unit is not in use, the gas must be turned off at the supply
cylinder. Storage of this unit indoors is permissible only if the cylinder
is disconnected and removed. Cylinders must be stored outdoors,
out of reach of children and must not be stored in a building, garage
or any other enclosed area.
End of Season Storage
Refer to the shut down instructions above prior to closing the
propane tank valve and disconnecting the regulator. Close the
propane tank valve and disconnect regulator. Also disconnect
the battery but make sure not to remove battery from trap.
Any open Mosquito Magnet
®
attractant should be removed and
discarded. See attractant label for disposal instructions. The
bug bag should also be discarded prior to storing the trap.
STORAGE: The trap should be stored indoors in a garage or shed in
the off-season. Cover trumpet to prohibit insects from nesting. Cover
unit with trap cover or with a tarp and secure tightly at the bottom to
keep out dust, spider webs and other debris.
NOTE: It is recommended that you use the Quick Clear adapter
before seasonal storage to avoid build-up of
contaminants during off-season.
(see page 11).
**READ MANUAL BEFORE STARTING**
For Optimal Results Run 24 hours/day
• Your trap will begin capturing immediately with
significant reduction in the mosquito population in
7-10 days.
Allow 4 weeks to significantly reduce the
mosquito population in your yard.
• Allow trap to cool for 5 minutes before re-start.
• Never spray insecticide in or around trap.
• Trap can be left running in the rain, but do not place
trap directly above a water source (sprinklers, hose,
etc.).
• If using lime or fertilizer compounds, be sure to shut
down the trap first to prevent dust or fine mist from
being drawn into trap and clogging bug bag.
Warning: Improper installation, adjustment, alteration, service or
maintenence can cause injury or property damage. Read the
installation, operating and maintenence instructions thoroughly
before installing or servicing this equipment.
Caution: The gas pressure regulator provided with this
appliance must be used. This regulator is set for an outlet
pressure 11.0 in. water column.
The gas supply must be turned off at the LP-Gas supply
cylinder when this appliance is not in use.
7
Set-Up
Propane Tank Installation
1. After trap is placed in its ideal location,
place propane tank onto the base.
2. Making sure propane tank is fully closed, attach
propane regulator hose to propane tank. Secure
tightly by hand.
Do not use tools.
3. Turn propane on by slowly turning valve counter-
clockwise. Take care not to turn too quickly to avoid
engagement of safety valve.
DO NOT MOVE TRAP WITH TANK ATTACHED!
TANK MUST BE DISCONNECTED FROM REGULATOR
BEFORE TRAP IS RELOCATED TO AVOID DAMAGE
TO REGULATOR AND/OR TRAP. BE ADVISED,
DAMAGE CAUSED FROM FAILURE TO COMPLY
WITH THIS INSTRUCTION IS NOT COVERED
UNDER WARRANTY.
Step 1 – Propane Tank Placement
Step 2 – Attach Regulator
Step 3 – Slowly Open Valve