Woods 872298G Скачать руководство пользователя страница 7

Страница: 7 / 76

WOODS

SAFETY

Machine preparation

Check operator presence interlock system and
brake operation. Adjust or repair any problems
before using.

Do not tamper with or defeat safety devices.
Keep guards, shields and interlock safety devices
in place and in proper working condition. They
are for your protection.

Keep all fasteners such as nuts, bolts and pins
well secured.

Visually inspect blades, blade bolts and the cutter
assembly for wear or damage. Replace worn or
damaged blades and bolts to preserve balance.

Verify that machine and attachments, if any, are
in good operating condition.

Do not engage blades until ready to mow.

OPERATING SAFELY

In general

Use extra care when loading or unloading the
machine into a trailer or truck.

Slow down and use caution when making turns
and crossing roads and sidewalks. Stop blades if
not mowing.

Do not run the engine in an enclosed area where
dangerous carbon monoxide fumes can collect.

Do not place your foot on the ground while
operating the machine.

Before operating, lower the discharge chute,
install the mulcher or put the entire grass catcher
in place.

Keep clear of the discharge opening at all times.
Never direct the discharge toward a bystander.
Stop operation if someone approaches.

Keep washout ports and other mower housing
service openings closed when mowing.

Use care when pulling loads or using heavy
equipment.

- Use only approved drawbar hitch points.

- Limit loads to those you can safely control.

- Do not turn sharply. Use care when reversing.

- Use counterweight(s) or wheel weights when

suggested in the operator's manual.

Never leave a machine unattended. Always turn
off blades, set parking brake, stop engine and
remove key before dismounting.

Содержание 872298G













































































Результаты поиска

Содержание 872298G

Отзывы:

Бренды по названию

Популярные бренды

Woods 872298G, Руководство оператора

Результаты поиска

Содержание 872298G

Отзывы:

Бренды по названию

Популярные бренды