manualshive.com logo in svg

Woods 872298G, Руководство оператора

Поделиться
Скачать
Woods 872298G Скачать руководство пользователя страница 38

38

WOODS

HYDROSTATIC TRANSAXLE ADJUST-
MENTS

A turnbuckle style hydro stat neutral adjustment is 
provided.  

Neutral:

  

1.   Support the machine with the rear wheels off 

the ground.  Use jack stands or equivalent sup-
port.  Do not rely only on mechanical or hydraulic 
jacks.  

2.   Move the traction levers out into the neutral lock 

position and raise the seat.

3.   Disconnect the seat switch wire and temporarily 

connect the two terminals with jumper wire 

J

 as 

shown. 

4.  Start the engine and run at low speed.
5.  Move parking brake to the 

OFF

 position.  

6.  Loosen jam nuts 

K

 at both ends of the control 

rod 

L

.

7.  Rotate the control rod until the corresponding 

wheel stops turning.  Lock the control rod jam 
nuts.  Run the engine up to high idle and stroke 
the traction levers forward and back to check the 
adjustment.  Move traction levers back to neutral 
and readjust if necessary.  

8.  Repeat steps 6 and 7 for the opposite side.
9.  Remove the jumper wire and reconnect the seat 

switch.

ADJUSTMENTS

Содержание 872298G













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды