Woodhaven 4965 Super Sled Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 8

Woodhaven 4965 Super Sled Скачать руководство пользователя страница 8

OPTIONAL ACCESSORIES

The

6305R Riser Kit

increases the capacity of the toggle clamps to 2-3/4" thick stock.

The

3690 Mite-R-Gage

is a handy tool for setting odd angles not covered by the indexing holes in the Super Sled. The

789S

Flip Stop

is available for use with the Horizontal fence.

©Copyright WOODHAVEN INC. 9/25/12

(800)344-6657 or WWW.WOODHAVEN.COM

7

USING THE SUPER SLED FOR TAPERS

Set the Fence to the desired taper or angle. This is done by lining up the cut lines on your

work with the cut edge of the Sled Base, which is also the cut line of your saw. Position the fence

against the opposite side of the work and tighten. Adjust the Stop against the end of the work.

Position the handle and toggle clamps on the Fence where desired. Tighten the toggle clamps on the work using medium

pressure. Do not over tighten!

Make the cut, being sure that the work is not touching the blade before starting the cut.

9

789S Flip Stop

3690 Mite-R-Gage

«
...
6
7
8

Содержание 4965 Super Sled









Отзывы:

Нет отзывов