2
2
2
2
21
1
1
1
10 W
0 W
0 W
0 W
0 Wood County Industrial P
ood County Industrial P
ood County Industrial P
ood County Industrial P
ood County Industrial Park, P
ark, P
ark, P
ark, P
ark, P.O. Box 1
.O. Box 1
.O. Box 1
.O. Box 1
.O. Box 1686, P
686, P
686, P
686, P
686, Parkersburg, WV 26
arkersburg, WV 26
arkersburg, WV 26
arkersburg, WV 26
arkersburg, WV 261
1
1
1
102-1
02-1
02-1
02-1
02-1686
686
686
686
686
4
Top & Base Assembly
3
Finishing
4
Mounting The Dial & Movement
5
1.
1.
1.
1.
1. Position the plywood dial board (#8) into the clock so that the top edge of the dial board is tight against the interior top.
Mark the location of the predrilled holes on the back of the clock front.
2.
2.
2.
2.
2. Using a sharp scratch awl, put a
1
/
4
" deep starter hole at each location. You can drill
You can drill
You can drill
You can drill
You can drill
a starter hole with an
a starter hole with an
a starter hole with an
a starter hole with an
a starter hole with an
7
77
7
7
/
//
/
/
64
64
64
64
64
" bit, but take great care not to drill through the clock
" bit, but take great care not to drill through the clock
" bit, but take great care not to drill through the clock
" bit, but take great care not to drill through the clock
" bit, but take great care not to drill through the clock
front.
front.
front.
front.
front.
3.
3.
3.
3.
3. Mount quartz movement and dial to the dial board as shown in the diagram (right). It
is not necessary to glue the dial face to the dial board. The shaft nut of the quartz
movement and pressure of the dial board against the back of the clock front will hold
the dial in position.
4.
4.
4.
4.
4. Position the dial board/dial/movement assembly into position and screw in place with (4) #6 x 1" brass wood screws.
5.
5.
5.
5.
5. If the dial is not aligned properly loosen the dial board wood screws and the movement shaft nut and reposition the dial.
When the dial alignment is correct, tighten the wood screws and shaft nut.
6.
6.
6.
6.
6. Cut pendulum shaft to length. Proper length shaft will result in pendulum bob centered in smaller circular opening on the
clock front. Install “AA” battery.
Case Back Installation
6
1.
1.
1.
1.
1. Insert the plywood case back into rear of case and check for fit. It should not fit too tightly.
Mark starter hole locations in the interior top and base.
2.
2.
2.
2.
2. Remove the plywood case back and drill
5
/
64
" starter holes
1
/
4
" deep as marked.
3.
3.
3.
3.
3. Install case back using (2) #4 x
5
/
8
" brass flat head wood screws.
DO NOT GLUE THE CASE BACK IN PLACE!
DO NOT GLUE THE CASE BACK IN PLACE!
DO NOT GLUE THE CASE BACK IN PLACE!
DO NOT GLUE THE CASE BACK IN PLACE!
DO NOT GLUE THE CASE BACK IN PLACE!
1.
1.
1.
1.
1. Position the glued case assembly onto the clock base (#1) so that the case is centered side to
side on the base. All of the edges on the base have been slightly “relieved” with the exception of
the back edges. Ensure that the non-relieved, square, back edges are oriented toward the back
of the clock and flush with the rear edge of the side panels.
2.
2.
2.
2.
2. With the case in position, carefully mark the position of the predrilled holes on the interior
base. Using a
7
/
64
" bit drill a
1
/
4
" deep starter hole for each predrilled hole.
3.
3.
3.
3.
3. Spread a thin film of glue on the base of the case, place the case on the base and screw in
position with 2 #6 x
5
/
8
" brass, flat head wood screws.
4.
4.
4.
4.
4. Position the bevel edge top (#2) on the case so that the non beveled, square edge is oriented
to the rear of the clock and flush with the rear edge of the side panels.
5.
5.
5.
5.
5. With the top in position, carefully mark the position of the predrilled holes of the interior top.
Using a
7
/
64
" bit drill a
1
/
4
" deep starter hole for each predrilled hole.
6.
6.
6.
6.
6. Spread a thin film of glue on the top of the case, place the top on the case and screw in
position with 2 #6 x
5
/
8
" brass, flat head wood screws.
The Mission Mantle Clock may be left natural or stained according to your preference. For our catalog photograph, we utilized a
golden oak Gel Finish (Woodcraft stock # 34M13). When staining the wood, we recommend you experiment with scrap or the
inside of the case until you are sure of the results. All visible areas should be finished, the dial board may be left unfinished.
