Woodbridge BID 02 Скачать руководство пользователя страница 12

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

TROUBLESHOOTING  GUIDE

a

b

c

Note:

        Cut off power prior to discharging 

        the water. 

Self-cleaning waterway maintenance

Self-cleaning Waterway Maintenance

When the self-cleaning waterway is blocked, 

there is no water coming out during self-cleaning 

process.

Current-limiting nut

Current-limiting shaft

Deodorizing Device Maintenance

Removal and Installation of Clamp

Unscrew the screws, take out the deodorant box, and replace the none-photocatalyst.

 It is recommended to replace the none-photocatalyst after 3 years of use (the specific life 

    span depends on the environment).

 If you need to replace the none-photocatalyst, please purchase it in the official online store.

1. Turn off  the angle valve.

2. Unplug the power plug, cut off  the power.

3. Remove the seat, press current-limiting shaft in the middle with a flat-blade screwdriver, then reinstall the seat, and open 

     the inlet valve.

4. If there is still no water coming out after pressing current-limiting shaft, use a flat-blade screwdriver to unscrew current-limiting 

    nut, remove current-limiting shaft, and clean it with a toothbrush or small brush. After cleaning, replace current -limiting 

    nut and current-limiting shaft to the restrictor In the device, then reinstall the seat, and open the inlet valve.

Deodorizing 

cartridge

Removal: Open the clamp 

c o v e r ,   r o t a t e   i t  

counterclockwise, and use a 

flat-blade screwdriver to pry 

the clamp out of the slot.

I n s t a l l a t i o n :   I n s t a l l   t h e  

quick-released connector of 

water inlet pipe into the main 

unit, and clip the clamp into the 

slot.

b. The clamp is rotated until the 
     opening faces down.
 c. Close the clamp cover

None-photocatalyst 

www.woodbridgebath.com

11

Содержание BID 02















Отзывы: