manualshive.com logo in svg

Wood Stone MT. ADAMS, Инструкция по установке и эксплуатации

Поделиться
Скачать
Wood Stone MT. ADAMS Скачать руководство пользователя страница 11

Mountain Series 

Installation and Operation Manual

An ongoing program of product improvement may require us to change
specifications without notice. 

WS-MS-(4,5,6,7)-RFG-W,

Revised May 2015.                                     Doc no: M0032.02

[email protected]

 

or visit 

woodstone-corp.com

wood stone corporation

1801 w. bakerview rd.
bellingham, wa 98226 usa

tf. 800.988.8103
t. 360.650.1111
f. 360.650.1166

11

GAS SPECIFICATIONS

Model

SV-2

WS-MS-4-RFG-W-NG

5”

WS-MS-5-RFG-W-NG

4�75"

WS-MS-6-RFG-W-NG

4�75"

WS-MS-7-RFG-W-NG

4�6"

Model

SV-2

WS-MS-4-RFG-W-LP

7"

WS-MS-5-RFG-W-LP

8"

WS-MS-6-RFG-W-LP

8"

WS-MS-7-RFG-W-LP

9�5"

The Wood Stone Gas ovens are equipped with a 3/4" NPT gas connection located at the rear left of the oven� Have a 
licensed gas installer provide the hook-up and test all fittings and pipe connections for leaks� Use approved gas leak 
detectors (soap solutions or equivalent) over and around the fittings and pipe connections�

 DO NOT USE FLAME TO 

TEST FOR LEAKS!

SV-2 is the gas control valve that operates the interior radiant burner� SV-2 is located at the rear left beneath the oven� 

NOTE:

 

The gas valve is shipped in the

 

ON 

position�

The manifold pressure test port for the radiant burner is a 1/8" NPT plugged tap located at the base of the T-junction 
between the SV-2 and the radiant/interior burner�
The burner manifold pressure has been adjusted and tested at the factory� A variety of factors can influence this pressure, 
so be sure to test the burner manifold pressure and adjust the valve as necessary to achieve the specified pressure� 

NOTE: 

Maximum inlet gas pressure: 1/2 psi (14 inches W.C.) 

This oven requires no modifications or adjustments for use at high altitudes.

Factory specified individual burner manifold pressures (W.C.) for RFG-W models equipped to burn 
Natural Gas (NG)

Factory specified individual burner manifold pressures (W.C.) for RFG-W models equipped to burn 
Propane (LP & HLP)

Model

SV-2

WS-MS-4-RFG-W-HLP

7"

WS-MS-5-RFG-W-HLP

8"

WS-MS-6-RFG-W-HLP

8"

WS-MS-7-RFG-W-HLP

9�5"

Содержание MT. ADAMS

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды