Wood-mizer OS96 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 19

Wood-mizer OS96 Скачать руководство пользователя страница 12

Operation

Towing The Sawmill With Seat

1

1-10

96OS-969700doc020113

Operation

1.3

Towing The Sawmill With Seat

1.

Move the saw head to its towing position.

2.

Disconnect the seat from the sawmill carriage by pulling up on the seat latch and pulling
back on the seat. Move the seat back past the trailer wheel until the travel lock pin aligns
with the hole in sawmill frame tube.

if your sawmill does not have a hole in the

frame tube that aligns with the seat travel lock pin.

3.

Pull the travel lock pin out as far as it will go, rotate 1/2 turn, and release. The
spring-loaded pin should engage the hole in the sawmill frame tube.

See Figure 1-8.

4.

Remove the step retaining pins and lift the foot step to its travel position. Replace the
retaining pins.

To unlock the seat from the traveling position, pull the travel lock pin out as far as it will
go. Rotate 1/2 turn and release into the pin resting bracket. The bracket will keep the pin
from returning to the locking pin hole.

5.

Slide the seat back until the seat frame clears the sawmill fender by 2 to 3 inches.

6.

Pull the travel lock pin out as far as it will go, rotate 1/2 turn, and release. Mark the loca-
tion where the travel lock pin contacts the sawmill frame tube.

FIG. 1-8

Pull out and
rotate to engage
travel lock pin

3H0448

«
...
10
11
12
13
14
...
»

Содержание OS96




















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды