Wood-mizer OS96 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 19

Wood-mizer OS96 Скачать руководство пользователя страница 10

Operation

Installation

1

1-8

96OS-969700doc020113

Operation

10.

Connect the seat to the sawmill carriage. Lift up on the seat latch, and move the seat in
toward the carriage until the latch hook is underneath the track roller housing. Release
the latch.

See Figure 1-6.

Make sure the seat is securely fastened to the carriage and there is no

looseness between the seat and the sawmill carriage. Use the latch adjustment bolt to
adjust the latch. Loosen the jam nut on the latch adjustment bolt. Turn the adjustment bolt
out as desired. Check the seat for looseness. Repeat as necessary until the seat is
securely fastened to the carriage. Retighten the jam nut.

11.

An adjustment handle is provided to allow the operator to slide the seat forward or back.
Pull the handle to the side and adjust the seat as desired. Release the handle.

FIG. 1-6

3H0107

Latch adjustment bolt

Seat latch

«
...
8
9
10
11
12
...
»

Содержание OS96




















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды