Wood-mizer MK20-2 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 86

background image

Installation and Setup

Exhaust Module Installation

3

3-17

WMDKdoc020322

Installation and Setup

3.8

Exhaust Module Installation



Drill a hole (

102mm) for the exhaust fan through the wall of the kiln. Mount the

sliding exhaust valve to the outside chamber wall. To do that, position the valve on
the chamber wall, mark and drill the mounting holes. Drill only through the outer skin
of the kiln using a 11 mm drill bit. Next, install the rivet nuts (the squeeze size on the
riveter indicator should be set at 1 mm). Position the valve once more and check if
the Exhaust Vent Hole Liner length fit the chamber wall thickness (the hole liner
should not protrude from the hole in the chamber wall. If the hole liner is too long cut
it to the proper length. Apply a silicone sealant to the hole liner and insert into the
hole from the outside of the kiln.

FIG. 3-16

∅

Exhaust Vent Hole Liner

Silicone sealant

WDK011

«
...
26
27
28
29
30
...
»

Содержание MK20-2























































































Отзывы:

Нет отзывов

Похожие инструкции для MK20-2

Бренд: PALSON Страницы: 52

Бренд: Lotus Страницы: 22

ItaliaBrava Ferrari BABFB1BE

Бренд: BaByliss PRO Страницы: 60

Бренд: Premier Страницы: 7

Бренд: Daewoo Страницы: 12

SE1200 Easy Breeze

Бренд: Hoefer Страницы: 27

Beautiful TriZone

Бренд: Sensio Страницы: 80

Бренд: MBM Страницы: 74

Бренд: GE Страницы: 8

DPGT650GHMG - 27" Gas Dryer

Бренд: GE Страницы: 4

Бренд: GE Страницы: 8

Бренд: GE Страницы: 9

Бренд: GE Страницы: 8

Бренд: GE Страницы: 16

Бренд: GE Страницы: 11

Бренд: GE Страницы: 8

Бренд: GE Страницы: 8

Бренд: GE Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды