manualshive.com logo in svg

Wood-mizer BMT100-2, Руководство по эксплуатации, частям и обслуживанию

Поделиться
Скачать
Wood-mizer BMT100-2 Скачать руководство пользователя страница 5

Setup

Toothsetter Mount

Setup

BMT10013doc082115

2-1

2

SECTION 2   SETUP

2.1

Toothsetter Mount

Install the crank handle to the toothsetter crank assembly using the supplied hex head
bolt. Be sure the handle is oriented in the "up" position as shown. Install the crank handle
knob to the crank handle using the provided socket head bolt and two hex nuts.

Mount the toothsetter to the stand. Use the mounting holes found in the base plate of the
setting fixture. Use the provided bolts (inserting the bolts down through the top of the
mounting plate), hex nuts. Setup the toothsetter so that there is at least 32" (81.0 cm) to
the rear and to either side of the tool. This allows enough room for the blade supports.

See Figure 2-1. 

FIG. 2-1 BMT100-2

BMT008-1

Hex Nut (2)

Mounting Bolt (2)

Hex Nut (2)

Toothsetter
Stand

Hex Head Bolt

Socket Head Bolt

Toothsetter

Crank
Handle

Crank Handle
Knob

Содержание BMT100-2





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды