9-pin D-Sub connector
on unit; male
(front side)
5
9
2
7
3 4
8
1
6
The complete serial protocol can be found on our internet homepage:
www.wolfvision.com/support
The serial port
(#19)
can be used to control the Visualizer through an external device, such
as a room control system that are used to integrate converence rooms.
Please note that ecim
odes (=ASCII odes or Hex odes)
must be sent as one single byte (e.g. 199 and not: 1 + 1 + 9) !
Pins:
2: RX, 3: TX, 5: GND
Baud Rate:
9200, 19200, 38400, 57600 or 115200 (selectable)
databits: 8, stopbit: 1, parity: no
The baud rate can be changed in the on-screen extra menu
(see page 15)
.
d
al c
c
c
PAL / NTSC Video Outputs
VZ-C32 only
RS 232, Serial Control Input
DVI Port
1
- T.M.D.S. Data2-
9
-
T.M.D.S. Data1-
17
- T.M.D.S. Data0-
2
- T.M.D.S. Data2+
10
-
T.M.D.S. Data1+
18
- T.M.D.S. Data0+
3
- T.M.D.S. Data2/4 Shield
11
-
T.M.D.S. Data1/3 Shield
18
- T.M.D.S. Data0+
4
- T.M.D.S. Data4-
(*)
12
- T.M.D.S. Data3-
(*)
19
- T.M.D.S. Data0/5 Shield
5
- T.M.D.S. Data4+
(*)
13
- T.M.D.S. Data3+
(*)
20
- T.M.D.S. Data5-
(*)
6
- DDC Clock
14
- +5V Power
21
- T.M.D.S. Data5+
(*)
7
- DDC Data
15
- Ground (return for +5V,
22
- T.M.D.S. Clock+
8
- Analog Vertical Sync
HSync and Vsync)
23
- T.M.D.S. Clock-
C1
- Analog Red
16
- Hot Plug Detect
24
- Analog Vertical Sync
C4
- Analog Horizontal Sync
C2
- Analog Green
C3
- Analog Blue
C5 - Analog Ground
*...not used
(analog R, G & B return)
m
Pin 24
Pin 8
Pin 1
Pin 9
Pin 17
C4
C1
C2
C3
C5
The S-video (Y/C)
(#21)
and Composite
(#17)
video outputs can be switched between PAL
and NTSC in the units on-screen menu
(see page 15)
.
Please note, that the picture quality of the S-video
(#21)
output is BETTER than the quality
of the Composite
(#17)
video output. However the picture quality of both video outputs is BY
FAR NOT AS GOOD as the picture quality of the data outputs
(#16, #18, #22 and #23).
This
is because of the limitations of the PAL/NTSC video system and because of the fact that
this is just a converted Progressive Scan signal and not an original video signal.
By default, the video output is switched off and can be activated in the on-screen menu
(see page 15)
.
Lightbox (optional)
When a lightbox is used, the top light of the Visualizer should be switched off
with the LIGHT
key
(#33)
.
Using a bottom light has the disadvantage that the Synchronized Lightfield of the top light
no longer marks the pick-up area of the built-in camera.
When switching off the top light, the Ceiling Visualizer also switches the white balance
adjustment from "one-push" white balance to "auto-tracking" white balance. This
compensates the varying color temperatures of different light sources -
see page 11.
The recommended lightbox for the Ceiling Visualizer is the WolfVision Lightbox LB-38.
14