Wolf Rangetop Скачать руководство пользователя

Страница: 18 / 29

Connect the electrode wire to the spark module.

SPARK MODULE MOUNTING BRACKET REMOVAL

To remove the spark module mounting bracket, first remove:

Burner grate

above spark module mounting bracket to be

replaced

Burner caps

Burner assemblies

Burner pan

above spark module mounting bracket to be

replaced

Both

spark modules

on the spark module mounting bracket

to be replaced

Remove the Spark Module Mounting Bracket

Use a T-15 Torx bit to remove the screws from the spark
module mounting bracket.

Remove the spark module mounting bracket from the unit.

SPARK MODULE MOUNTING BRACKET INSTALLATION

Install the Spark Module Mounting Bracket

Place the spark module mounting bracket into the unit.

Use a T-15 Torx bit to install the screws into the spark
module mounting bracket.

WIRING COVER REMOVAL

To remove the wiring cover for a 48" unit, first remove on the
right-hand side:

To remove the wiring cover for a 36" unit, first remove:

Remove the Wiring Cover

Use a

" socket to remove the wiring cover mounting

screws.

Remove the wiring cover from the unit.

WIRING COVER INSTALLATION

Install the Wiring Cover

Place the wiring cover over the grounding plate.

Use a

" socket to install the wiring cover mounting

screws.

POWER CORD REMOVAL

To remove the power cord for a 48" unit, first remove on the
right-hand side:

To remove the power cord for a 36" unit, first remove:

Sealed Burner Rangetop with Wok Service Manual

Component Removal and Installation

INSTALL THE SPARK MODULE (continued)

service.subzero.com

828990 REV. A

Содержание Rangetop






























Результаты поиска

Содержание Rangetop

Отзывы:

Похожие инструкции для Rangetop

Бренды по названию

Популярные бренды

Wolf Rangetop, Руководство по обслуживанию

Результаты поиска

Содержание Rangetop

Отзывы:

Похожие инструкции для Rangetop

Бренды по названию

Популярные бренды