Wolf I363418, Руководство по установке, Страница: 9 / 15

9
R E M O T E B L O W E R
IMPORTANT NOTE: Before turning
the power on, make sure the blower
is in the "OFF" position. Use wire con-
nectors or wire nuts approved by UL
or C/UL. Refer to installation instruc-
tions provided with each blower to
verify island or roof cut-outs.
STEP 1: Plan the Installation
1) Locate the blower so the length of
the duct run and number of elbows
and transitions are kept to a mini-
mum.
2) Where possible, blower should be
located between island studs or roof
rafters.
3) Avoid pipes, wires or other duct-
work that may be running through
the island.
4) Be sure that there is enough space
for any transitions that may be need-
ed between the blower and the con-
necting ductwork.
5) For best performance, locate tran-
sitions nearest the blower.
STEP 2: Connect Remote Blower
NOTE: Always refer to all blower
installation instructions provided with
the blower for additional mounting
and wiring instructions.
1) Remove cover from wiring box
inside of hood shell. Remove wiring
box knockout.
2) Feed 20” of inbound (Romex)
power cable through the knockout
opening hole and into the wiring
box. Secure the cable to wiring box
with an appropriate connector for
type of cable being used.
Connect
leads as follows:
• Black (L1) to black (loose) in the J
box from the switch.
• Neutral to neutral (loose) in the J
box from the switch.
3) Wiring Remote Blower: Follow
wiring instructions at the blower as
outlined in the particular blower
installation instructions. Black (L1) to
black, white (neutral) to white – or
white to blue, or white to brown
(depending on model) and green to
grounding screw. Run remote blower
cable (ROMEX) to the hood.
Feed 20”of (ROMEX) power cable
through the knockout opening hole
and into the wiring box on the
rough-in plate of hood. Secure the
cable to wiring box with an appropri-
ate connector.
Locate cord assembly provided with
the remote blower. The cord assem-
bly has two leads, black (L1) and
white (neutral). Connect these leads
to the leads from the blower, black to
black and white to white.
Connect ALL green and bare wires
together to the ground screw in the
wiring box.
4) Plug cord assembly into receptacle
located near the center of the hood
shell. Use clips on hood interior to
keep excess power cord away from
moving parts.
5) Re-install wiring box cover and
screws. Make sure all wires are secure
and that no wires are pinched
between cover and box.
24
1/2
"(622)
15
1/2
"(394)
28
1/4
"(717)
20
3/4
"(527)
24
3/4
"(629)
14"(356)
4
3/4
"(121)
10"(254)
DIAMETER
Remote blower dimensions – 600 CFM (801640) and
900 CFM (801641)
10"(254)
DIAMETER
14
3/4
"(375)
29
1/2
"(749)
29
1/2
"(749)
18"(457)
22"(559)
10
1/8
"(257)
7
1/4
"(184)
10"(254)
Remote blower dimensions – 1200 CFM
(801642)
10"(254)
DIAMETER
14
3/4
"(375)
29
1/2
"(749)
29
1/2
"(749)
21"(533)
25"(635)
10
3/8
"(264)
7
1/4
"(181)
10"(254)
Remote blower dimensions – 1500 CFM
(804701)
P
R O
S
E R I E S
I
S L A N D
H
O O D
I
N S T A L L A T I O N